EDDI

Energy Dispersive Diffraction

Publications

2023

Schmidt, Jonas: Verformungsmechanismen und mechanische Eigenschaften stranggepresster Seltene-Erden-haltiger Magnesiumlegierungen. , TU Berlin, 2023

Genzel, C.; Klaus, M.; Hempel, N.; Nitschke-Pagel, T.; Pantleon, K.: Energy-dispersive X-ray stress analysis under geometric constraints: exploiting the material’s inherent anisotropy. , Journal of Applied Crystallography 56 (2023), p. 526-538
doi: 10.1107/S1600576723001759

Dong, K.; Sun, F.; Hilger, A.; Kamm, P.H.; Osenberg, M.; García-Moreno, F.; Manke, I.: Tracking the phase transformation and microstructural evolution of Sn anode using operando synchrotron X-ray energy-dispersive diffraction and X-ray tomography. , Journal of Energy Chemistry 76 (2023), p. 429-437
doi: 10.1016/j.jechem.2022.10.014

2022

Marciszko-Wiackowska, M.; Oponowicz, A.; Baczmanski, A.; Braham, C.; Watroba, M.; Wróbel, M.; Klaus, M.; Genzel, Ch.: A novel approach for nondestructive depth-resolved analysis of residual stress and grain interaction in the near-surface zone applied to an austenitic stainless steel sample subjected to mechanical polishing. , Measurement : Journal of the International Measurement Confederation (IMEKO) 194 (2022), p. 111016/1-21
doi: 10.1016/j.measurement.2022.111016

Schäfer, Stefan Jerome: Diffusion Modeling in Stressed Chalcogenide Thin-Films. , HU Berlin, 2022

2021

Millán, L.; Bokuchava, G.; Fernández, R.; Papushkin, I.; González-Doncel, G.: Further insights on the stress equilibrium method to investigate macroscopic residual stress fields: Case of aluminum alloys cylinders. , Journal of Alloys and Compounds 861 (2021), p. 158506/1-12
doi: 10.1016/j.jallcom.2020.158506

Klaus, Manuela: Nondestructive analysis of near surface residual stress fields in polycrystalline materials with X-ray diffraction: Methodological challenges in the light of modern industrial research. , Habil.-Schrift, Berlin, Technische Universität Berlin, 2021

Schröder, J.; Mishurova, T.; Fritsch, T.; Serrano-Munoz, I.; Evans, A.; Sprengel, M.; Klaus, M.; Genzel, C.; Schneider, J.; Bruno, G.: On the influence of heat treatment on microstructure and mechanical behavior of laser powder bed fused Inconel 718. , Materials Science and Engineering A 805 (2021), p. 140555/1-15
doi: 10.1016/j.msea.2020.140555

Serrano-Munoz, I.; Fritsch, T.; Mishurova, T.; Trofimov, A.; Apel, D.; Ulbricht, A.; Kromm, A.; Hesse, R.; Evans, A.; Bruno, G.: On the interplay of microstructure and residual stress in LPBF IN718. , Journal of Materials Science 56 (2021), p. 5845–5867
doi: 10.1007/s10853-020-05553-y

Nitschke-Pagel, T.: Recommendations for the measurement of residual stresses in welded joints by means of X-ray diffraction—results of the WG6-RR test. , Welding in the World 65 (2021), p. 589–600
doi: 10.1007/s40194-020-01029-4

Nielsen, J.O.; Grumsen, F.B.; Pantleon, K.: Thermal evolution of ferrite in electrodeposited iron-carbon coatings in relation to phase transformations during post-deposition annealing. , Materials Characterization 172 (2021), p. 110886/1-8
doi: 10.1016/j.matchar.2021.110886

2020

Algashi, Alaa: Application of pn-CCD detector for imaging of nanowires using white synchrotron radiation. , Universität Siegen, 2020

Mishurova, T.; Artzt, K.; Haubrich, J.; Evsevleev, S.; Evans, A.; Meixner, M.; Munoz, I.S.; Sevostianov, I.; Requena, G.; Bruno, G.: Connecting Diffraction-Based Strain with Macroscopic Stresses in Laser Powder Bed Fused Ti-6Al-4V. , Metallurgical and Materials Transactions A 51 (2020), p. 3194-3204
doi: 10.1007/s11661-020-05711-6

El Azhari, I.; García, J.; Soldera, F.; Suarez, S.; Jiménez-Piqué, E.; Mücklich, F.; Llanes, L.: Contact damage investigation of CVD carbonitride hard coatings deposited on cemented carbides. , International Journal of Refractory Metals and Hard Materials 86 (2020), p. 105050/1-8
doi: 10.1016/j.ijrmhm.2019.105050

Mishurova, T.; Bruno, G.; Evsevleev, S.; Sevostianov, I.: Determination of macroscopic stress from diffraction experiments: A critical discussion. , Journal of Applied Physics 128 (2020), p. 025103/1-14
doi: 10.1063/5.0009101

Kratzig, A.; Hoa, L.Q.; Bettge, D.; Menneken, M.; Bäßler, R.: Early Stage of Corrosion Formation on Pipeline Steel X70 Under Oxyfuel Atmosphere at Low Temperature. , Procedia Engineering 8 (2020), p. 421/1-19
doi: 10.3390/pr8040421

Marschilok, A.C.; Bruck, A.M.; Abraham, A.; Stackhouse, C.A.; Takeuchi, K.J.; Takeuchi, E.S.; Croft, M.; Gallaway, J.W.: Energy dispersive X-ray diffraction (EDXRD) for operando materials characterization within batteries. , Physical Chemistry Chemical Physics 22 (2020), p. 20972-20989
doi: 10.1039/d0cp00778a

Nielsen, J.O.; Pantleon, K.: Evolution of hard Fe-C electrodeposits with temperature. , Surface Engineering 36 (2020), p. 960-965
doi: 10.1080/02670844.2019.1675305

Niessen, F.; Apel, D.; Danoix, F.; Hald, J.; Somers, M.A.J.: Evolution of substructure in low-interstitial martensitic stainless steel during tempering. , Materials Characterization 167 (2020), p. 110494/1-11
doi: 10.1016/j.matchar.2020.110494

Oponowicz, A.; Marciszko-Wiackowska, M.; Baczmanski, A.; Klaus, M.; Genzel, C.; Wronski, S.; Kollbek, K.; Wróbel, M.: Gradient of Residual Stress and Lattice Parameter in Mechanically Polished Tungsten Measured Using Classical X-rays and Synchrotron Radiation. , Metallurgical and Materials Transactions A 51 (2020), p. 5945-5957
doi: 10.1007/s11661-020-05967-y

Márquez, J.A.; Sun, J.P.; Stange, H.; Ali, H.; Choubrac, L.; Schäfer, S.; Hages, C.J.; Leifer, K.; Unold, T.; Mitzi, D.B.; Mainz, R.: High-temperature decomposition of Cu2BaSnS4 with Sn loss reveals newly identified compound Cu2Ba3Sn2S8. , Journal of Materials Chemistry A 8 (2020), p. 11346-11353
doi: 10.1039/d0ta02348e

Nielsen, J.O.; Christiansen, T.L.; Pantleon, K.: In Situ Analysis of the Thermal Evolution of Electrodeposited Fe-C Coatings. , Metallurgical and Materials Transactions A 51 (2020), p. 4880-4889
doi: 10.1007/s11661-020-05904-z

Levcenko, S.; Stange, H.; Choubrac, L.; Greiner, D.; Heinemann, M.D.; Mainz, R.; Unold, T.: Investigation of near-stoichiometric polycrystalline CuInSe2 thin films by photoreflectance spectroscopy. , Journal of Applied Physics 127 (2020), p. 125701/1-6
doi: 10.1063/1.5145208

El Azhari, Idriss: Multiscale mechanical and microstructural characterization of titanium and zirconium carbonitride hard coatings. , Universitat Politècnica de Catalunya (UPC), 2020

Carreón, H.; Carreon, M.L.; Carreon-Garcidueñas, M.: Nondestructive Magnetic Monitoring of Residual Stresses in a Medical Ti-6Al-4V-ELI Alloy Using a Fluxgate Sensor. , Physical Mesomechanics 23 (2020), p. 160-166
doi: 10.1134/s1029959920020071

Artzt, K.; Mishurova, T.; Bauer, P.P.; Gussone, J.; Barriobero-Vila, P.; Evsevleev, S.; Bruno, G.; Requena, G.; Haubrich, J.: Pandora's Box-Influence of Contour Parameters on Roughness and Subsurface Residual Stresses in Laser Powder Bed Fusion of Ti-6Al-4V. , Materials 13 (2020), p. 3348/1-24
doi: 10.3390/ma13153348

Levcenko, S.; Stange, H.; Choubrac, L.; Greiner, D.; Heinemann, M.D.; Mainz, R.; Unold, T.: Radiative recombination properties of near-stoichiometric CuInSe2 thin films. , Physical Review Materials 4 (2020), p. 064605
doi: 10.1103/physrevmaterials.4.064605

Pareek, D.; Taskesen, T.; Márquez, J.A.; Stange, H.; Levcenco, S.; Simsek, I.; Nowak, D.; Pfeiffelmann, T.; Chen, W.; Stroth, C.; Sayed, M.H.; Mikolajczak, U.; Parisi, J.; Unold, T.; Mainz, R.; Gütay, L.: Reaction Pathway for Efficient Cu2ZnSnSe4 Solar Cells from Alloyed Cu-Sn Precursor via a Cu-Rich Selenization Stage. , Solar RRL 4 (2020), p. 2000124/1-8
doi: 10.1002/solr.202000124

Elia, G.A.; Greco, G.; Kamm, P.H.; Garcia-Moreno, F.; Raoux, S.; Hahn, R.: Simultaneous X-Ray Diffraction and Tomography Operando Investigation of Aluminum/Graphite Batteries. , Advanced Functional Materials 30 (2020), p. 2003913/1-9
doi: 10.1002/adfm.202003913

Schäfer, S.; Stange, H.; Márquez, J.A.; Genzel, C.; Mainz, R.: Stress Formation During In-Ga Interdiffusion in Thin-Film CuIn1-xGaxSe2 Absorber Layers Leads to Stable Ga Gradients. , Physical Review Applied 14 (2020), p. 024063/1-17
doi: 10.1103/physrevapplied.14.024063

Nielsen, Jacob Obitsø: Surface engineering of Fe-C coatings. , Technical University of Denmark, 2020

Meng, Y.; Villa, M.; Dahl, K.V.; Christiansen, T.L.; Somers, M.A.J.: Synchrotron X-ray diffraction investigation of the effect of cryogenic treatment on the microstructure of Ti-6Al-4V. , Applied Surface Science 502 (2020), p. 144087/1-7
doi: 10.1016/j.apsusc.2019.144087

Serrano-Munoz, I.; Mishurova, T.; Thiede, T.; Sprengel, M.; Kromm, A.; Nadammal, N.; Nolze, G.; Saliwan-Neumann, R.; Evans, A.; Bruno, G.: The residual stress in as-built Laser Powder Bed Fusion IN718 alloy as a consequence of the scanning strategy induced microstructure. , Scientific Reports 10 (2020), p. 14645/1-15
doi: 10.1038/s41598-020-71112-9

2019

Sun, F.; He, X.; Jiang, X.; Osenberg, M.; Li, J.; Zhou, D.; Dong, K.; Hilger, A.; Zhu, X.; Gao, R.; Liu, X.; Huang, K.; Ning, D.; Markötter, H.; Zhang, L.; Wilde, F.; Cao, Y.; Winter, M.; Manke, I.: Advancing knowledge of electrochemically generated lithium microstructure and performance decay of lithium ion battery by synchrotron X-ray tomography. , Materials Today 27 (2019), p. 21-32
doi: 10.1016/j.mattod.2018.11.003

Dong, Kang: Characterization of battery anode materials by X-ray and electron-based imaging techniques. , Berlin, Technische Universität, Diss., 2019

Karl, D.; Jastram, B.; Kamm, P.H.; Schwandt, H.; Gurlo, A.; Schmidt, F.: Evaluating porous polylactide-co-glycolide/bioactive glass composite microsphere powders for laser sintering of scaffolds. , Powder Technology 354 (2019), p. 289-300
doi: 10.1016/j.powtec.2019.06.010

Shokr, Mohammad: From pnCCD to pnCCD + CsI(Tl) scintillator : characterizations and applications. , Siegen, Universität, Diss., 2019

Thielen, M.; Schaefer, F.; Gruenewald, P.; Laub, M.; Marx, M.; Meixner, M.; Klaus, M.; Motz, C.: In situ synchrotron stress mappings to characterize overload effects in fatigue crack growth. , International Journal of Fatigue 121 (2019), p. 155-162
doi: 10.1016/j.ijfatigue.2018.12.013

Moreno, Maiara Fernanda: In-situ Study of Residual Stress Evolution in Zr(C,N)/α-Al2O3 and Zr(C,N)/κ-Al2O3 CVD Multilayers during Thermal Cycling. , Brasilia, University of São Paulo (USP), Escola de Engenharia de São Carlos, 2019

Roy, S.; Gibmeier, J.; Schell, K.; Bucharsky, E.; Weidenmann, K.; Wanner, A.; Hoffmann, M.: Internal load transfer in an interpenetrating metal/ceramic composite material studied using energy dispersive synchrotron X-ray diffraction. , Materials Science and Engineering A 753 (2019), p. 247-252
doi: 10.1016/j.msea.2019.03.049

Falk, F.; Menneken, M.; Stefan-Scherb, C.: Real-Time Observation of High-Temperature Gas Corrosion in Dry and Wet SO2-Containing Atmosphere. , JOM 71 (2019), p. 1560-1565
doi: 10.1007/s11837-019-03335-9

Moreno, M.; Garcia, J.; Pinto, H.; Klaus, M.; Genzel, C.: Residual Stress Behavior of Cemented Carbide Coated with CVD Ti(C,N)/α-Al2O3 Multilayers: Effect Of Different Blasting Conditions. , In: Euro PM2019 proceedings : 13-16 October 2019, Maastricht, The Netherlands. Shrewsbury, United Kingdom: European Powder Metallurgy Association, 2019. - ISBN 978-1-899072-51-4, p. 1/6

Sun, F.; Gao, R.; Zhou, D.; Osenberg, M.; Dong, K.; Kardjilov, N.; Hilger, A.; Markötter, H.; Bieker, P.M.; Liu, X.; Manke, I.: Revealing Hidden Facts of Li Anode in Cycled Lithium–Oxygen Batteries through X-ray and Neutron Tomography. , ACS Energy Letters 4 (2019), p. 306-316
doi: 10.1021/acsenergylett.8b02242

Weber, Kathrin: Schädigungsmechanismen von Eisen-Chrom-Legierungen in sulfidierend-oxidierender Atmosphäre. , Berlin, Freie Universität Berlin, Diss., 2019

Félix, R.; Weber, A.; Zander, O.; Rodriguez-Álvarez, H.; Schubert, B.; Klaer, J.; Wilks, R.; Schock, H.; Mainz, R.; Bär, M.: Selenization of CuInS2 by rapid thermal processing - an alternative approach to induce a band gap grading in chalcopyrite thin-film solar cell absorbers? , Journal of Materials Chemistry A 7 (2019), p. 2087-2094
doi: 10.1039/c8ta10823d

Stange, H.; Brunken, S.; Greiner, D.; Heinemann, M.D.; Yani, D.A.B.; Waegele, L.A.; Li, C.; Sanli, E.S.; Kahnt, M.; Schmidt, S.S.; Baecker, J.-P.; Kaufmann, C.A.; Klaus, M.; Scheer, R.; Genzel, C.; Mainz, R.: Stacking fault reduction during annealing in Cu-poor CuInSe2 thin film solar cell absorbers analyzed by in-situ XRD and grain growth modeling. , Journal of Applied Physics 125 (2019), p. 035303/1-12
doi: 10.1063/1.5052245

Sonntag, Nadja: Untersuchung magnetischer Streufelder in einem inhomogen verformten Baustahl mittels passiv-magnetischer Prüfverfahren. , Berlin, Technische Universität, Diss., 2019

2018

Stange, Anna Helena: Analyse der Mikrostrukturentwicklung von CuInSe2 mittels in-situ Röntgenbeugung. , Berlin, Technische Universität, Diss., 2018

Garces, G.; Mathis, K.; Medina, J.; Horvath, K.; Drozdenko, D.; Onorbe, E.; Dobron, P.; Perez, P.; Klaus, M.; Adeva, P.: Combination of in-situ diffraction experiments and acoustic emission testing to understand the compression behavior of Mg-Y-Zn alloys containing LPSO phase under different loading conditions. , International Journal of Plasticity 106 (2018), p. 107-128
doi: 10.1016/j.ijplas.2018.03.004

Sun, F.; Osenberg, M.; Dong, K.; Zhou, D.; Hilger, A.; Jafta, C.J.; Risse, S.; Lu, Y.; Markötter, H.; Manke, I.: Correlating Morphological Evolution of Li Electrodes with Degrading Electrochemical Performance of Li/LiCoO2 and Li/S Battery Systems: Investigated by Synchrotron X-ray Phase Contrast Tomography. , ACS Energy Letters 3 (2018), p. 356-365
doi: 10.1021/acsenergylett.7b01254

Mainz, R.; Stange, H.; Kaufmann, C.A.: Defect Annihilation by Preferential Grain Growth during Cu(In, Ga)Se2 Co-evaporation. , In: 2018 IEEE 7th World Conference on Photovoltaic Energy Conversion (WCPEC) : (a joint conference of 45th IEEE PVSC, 28th PVSEC & 34th EU PVSEC) : 10-15 June 2018. Piscataway, NJ: IEEE, 2018. - ISBN 978-1-5386-8529-7, p. 3875-3879
doi: 10.1109/PVSC.2018.8547783

Kamm, Paul Hans: Der Schäumprozess von Aluminiumlegierungen : Tomoskopische Untersuchung der Gasnukleation. , Berlin, Technische Universität, Diss., 2018

Villa, M.; Niessen, F.; Somers, M.A.J.: In Situ Investigation of the Evolution of Lattice Strain and Stresses in Austenite and Martensite During Quenching and Tempering of Steel. , Metallurgical and Materials Transactions A 49 (2018), p. 28-40
doi: 10.1007/s11661-017-4387-0

Bäcker, Jan-Peter: In situ investigation of the rapid thermal reaction of Cu-In-Ga precursors to Cu(In,Ga)Se2 thin-film solar cell absorbers. , Berlin, Freie Universität Berlin, Diss., 2018

Niessen, F.; Villa, M.; Danoix, F.; Hald, J.; Somers, M.: In-situ analysis of redistribution of carbon and nitrogen during tempering of low interstitial martensitic stainless steel. , Scripta Materialia 154 (2018), p. 216-219
doi: 10.1016/j.scriptamat.2018.06.004

Alvares Ferreira, E.; Yokaichiya, F.; Marumo, J.; Vicente, R.; Garcia-Moreno, F.; Kamm, P.; Klaus, M.; Russina, M.; Günther, G.; Jimenez, C.; Franco, M.: Influence of the irradiation in cement for the Brazilian radioactive waste repositories: Characterization via X-ray diffraction, X-ray tomography and quasielastic neutron scattering. , Physica B 551 (2018), p. 256-261
doi: 10.1016/j.physb.2018.01.018

Niessen, F.; Villa, M.; Somers, M.: Martensite Formation from Reverted Austenite at Sub-zero Celsius Temperature. , Metallurgical and Materials Transactions A 49 (2018), p. 5241-5245
doi: 10.1007/s11661-018-4887-6

Bernardo, V.; Mugica, M.; Perez-Tamarit, S.; Notario, B.; Jimenez, C.; Rodriguez-Perez, M.A.: Nanoclay intercalation during foaming of polymeric nanocomposites studied in-situ by synchrotron X-ray diffraction. , Materials 11 (2018), p. 2459/1-12
doi: 10.3390/ma11122459

Niessen, Frank: Phase transformations in supermartensitic stainless steels. , Kongens Lyngby, Technical University of Denmark (DTU), thesis, 2018

Stephan-Scherb, C.; Nützmann, K.; Kranzmann, A.; Klaus, M.; Genzel, C.: Real time observation of high temperature oxidation and sulfidation of Fe-Cr model alloys. , Materials and Corrosion = Werkstoffe und Korrosion 69 (2018), p. 678-689
doi: 10.1002/maco.201709892

Apel, D.; Meixner, M.; Liehr, .; Klaus, M.; Degener, S.; Wagener, G.; Franz, C.; Zinn, W.; Genzel, C.; Scholtes, B.: Residual stress analysis of energy-dispersive diffraction data using a two-detector setup: Part I - Theoretical concept. , Nuclear Instruments & Methods in Physics Research A 877 (2018), p. 24-33
doi: 10.1016/j.nima.2017.09.005

Mishurova, T.; Cabeza, S.; Thiede, T.; Nadammal, N.; Kromm, A.; Klaus, M.; Genzel, C.; Haberland, C.; Bruno, G.: The Influence of the Support Structure on Residual Stress and Distortion in SLM Inconel 718 Parts. , Metallurgical and Materials Transactions A 49 (2018), p. 3038-3046
doi: 10.1007/s11661-018-4653-9

Sonntag, N.; Cabeza, S.; Kuntner, M.; Mishurova, T.; Klaus, M.; Kling e Silva, L.; Skrotzki, B.; Genzel, C.; Bruno, G.: Visualisation of deformation gradients in structural steel by macroscopic magnetic domain distribution imaging (Bitter technique). , Strain 54 (2018), p. e12296/1-15
doi: 10.1111/str.12296

Sun, F.; Dong, K.; Osenberg, M.; Hilger, A.; Risse, S.; Lu, Y.; Kamm, P.H.; Klaus, E.; Markötter, H.; Garcia-Moreno, F.; Arlt, T.; Manke, I.: Visualizing the morphological and compositional evolution of the interface of InLi-anode|thio-LISION electrolyte in an all-solid-state Li–S cell by in operando synchrotron X-ray tomography and energy dispersive diffraction. , Journal of Materials Chemistry A 6 (2018), p. 22489-22496
doi: 10.1039/c8ta08821g

Dixneit, Jonny: Wärmeführung und Beanspruchung von hochfesten Verbindungen mit LTT-Schweißzusatzwerkstoff. , Magdeburg, Otto-von-Guericke-Universität, Diss., 2018

2017

Fernandez, R.; Ferreira-Barragans, S.; Ibanez, J.; Gonzalez-Doncel, G.: A multi-scale analysis of the residual stresses developed in a single-phase alloy cylinder after quenching. , Materials & Design 137 (2017), p. 117 - 127
doi: 10.1016/j.matdes.2017.10.013

Mishurova, T.; Cabeza, S.; Artzt, K.; Haubrich, J.; Klaus, M.; Genzel, C.; Requena, G.; Bruno, G.: An assessment of subsurface residual stresses analysis in SLM Ti-6Al-4V. , Materials 10 (2017), p. 348/1-14
doi: 10.3390/ma10040348

Ahmad, B.; Fitzpatrick, M.E.: Analysis of Residual Stresses in Laser-Shock-Peened and Shot-Peened Marine Steel Welds. , Metallurgical and Materials Transactions A 48 (2017), p. 759-770
doi: 10.1007/s11661-016-3867-y

Shokr, M.; Schlosser, D.; Abboud, A.; Algashi, A.; Tosson, A.; Conka, T.; Hartmann, R.; Klaus, M.; Genzel, C.; Strüder, L.; Pietsch, U.: Applications of a pnCCD detector coupled to columnar structure CsI(Tl) scintillator system in ultra high energy X-ray Laue diffraction. , Journal of Instrumentation 12 (2017), p. P12032/1-14
doi: 10.1088/1748-0221/12/12/P12032

Liehr, Andreas: Beitrag zur randnahen Struktur- und Eigenspannungsanalyse in polykristallinen Werkstoffen mit energiedispersiven röntgenografischen Verfahren. , Kassel, Universität Kassel, Diss., 2017

Márquez, J.; Stange, H.; Hages, C.; Schaefer, N.; Levcenko, S.; Giraldo, S.; Saucedo, E.; Schwarzburg, K.; Abou-Ras, D.; Redinger, A.; Klaus, M.; Genzel, C.; Unold, T.; Mainz, R.: Chemistry and dynamics of Ge in kesterite: towards band gap graded absorbers. , Chemistry of Materials 29 (2017), p. 9399-9406
doi: 10.1021/acs.chemmater.7b03416

Okoro, S.C.; Niessen, F.; Villa, M.; Apel, D.; Montgomery, M.; Frandsen, F.J.; Pantleon, K.: Complementary Methods for the Characterization of Corrosion Products on a Plant-Exposed Superheater Tube. , Metallography, Microstructure, and Analysis 6 (2017), p. 22-35
doi: 10.1007/s13632-016-0325-6

Ocaña, J.; González-Carrasco, J.; Lieblich, M.; Barriuso, S.; Porro, J.; de Lara, L.; Díaz, M.; Santiago, J.: Compressive Residual Stresses and Associated Surface Modifications Induced in Ti6Al4V by Laser Shock Processing. , In: C. Sommitsch ... [Ed.] : THERMEC 2016 : selected peer reviewed papers from the 9th International Conference on Processing & Manufacturing of Advanced Materials, May 29-June 03, 2016, Graz, Austria. Zürich: Trans Tech Publications, 2017 (Materials science forum ; 879). - ISBN 978-3-0357-1129-5, p. 1408-1413
doi: 10.4028/www.scientific.net/MSF.879.1408

Scherg-Kurmes, Harald: Deposition von transparenten leitfähigen Oxiden mit hoher Ladungsträgermobilität bei niedriger Prozesstemperatur und deren Integration in Photovoltaik-Zellen : numerische Simulation der physikalischen und chemischen Vorgänge während der Deposition. , Berlin, Technische Universität, Diss., 2017

Toparli, B.M.; Smyth, N.; Fitzpatrick, M.E.: Effect of Treatment Area on Residual Stress and Fatigue in Laser Peened Aluminum Sheets. , Metallurgical and Materials Transactions A 48 (2017), p. 1519-1523
doi: 10.1007/s11661-017-3962-8

Liehr, A.; Zinn, W.; Degener, S.; Scholtes, B.; Niendorf, T.; Genzel, C.: Energy resolved residual stress analysis with laboratory X-ray sources = Eigenspannungsanalysen unter Verwendung energieauflösender Detektoren und Laborröntgenquellen. , HTM Journal of Heat Treatment and Materials 72 (2017), p. 115-121
doi: 10.3139/105.110316

Heinemann, M.D.; Mainz, R.; Österle, F.; Rodriguez-Alvarez, H.; Greiner, D.; Kaufmann, C.A.; Unold, T.: Evolution of opto-electronic properties during film formation of complex semiconductors. , Scientific Reports 7 (2017), p. 48463/1-9
doi: 10.1038/srep45463

Niessen, F.; Villa, M.; Apel, D.; Keßler, O.; Reich, M.; Hald, J.; Somers, M.A.J.: In Situ Techniques for the Investigation of the Kinetics of Austenitization of Supermartensitic Stainless Steel. , Materials Science Forum 879 (2017), p. 1381-1386
doi: 10.4028/www.scientific.net/MSF.879.1381

Niessen, F.; Villa, M.; Hald, J.; Somers, M.A.J.: Kinetics analysis of two-stage austenitization in supermartensitic stainless steel. , Materials & Design 116 (2017), p. 8–15
doi: 10.1016/j.matdes.2016.11.076

Gibmeier, J.; Rebelo-Kornmeier, J.; Strauss, T.: Local Residual Stress Depth Distribution in the Inner Gearing of a Case Hardened Sliding Collar "EDDI". , In: C. Sommitsch ... [Ed.] : THERMEC 2016 : selected peer reviewed papers from the 9th International Conference on Processing & Manufacturing of Advanced Materials, May 29-June 03, 2016, Graz, Austria. Zurich: TransTech Publ., 2017 (Materials science forum ; 879,1). - ISBN 978-3-0357-1129-5, p. 601-606
doi: 10.4028/www.scientific.net/MSF.879.601

Biberger, J.; Füßer, H.-J.; Klaus, M.; Genzel, C.: Near-Surface and Depth-Dependent Residual Stress Evolution in a Piston Ring Hard Chrome Coating Induced by Sliding Wear and Friction. , Wear 376-377 (2017), p. 1502-1521
doi: 10.1016/j.wear.2017.01.056

Klaus, M.; Genzel, C.: Nondestructive Separation of Residual Stress and Composition Gradients in Thin Films by Angle- and Energy-Dispersive X-Ray Diffraction. I. Theoretical Concepts. , Journal of Applied Crystallography 50 (2017), p. 252-264
doi: 10.1107/S1600576716020598

Klaus, M.; Genzel, C.; García, J.: Nondestructive Separation of Residual Stress and Composition Gradients in Thin Films by Angle- and Energy-Dispersive X-Ray Diffraction. II. Experimental Validation. , Journal of Applied Crystallography 50 (2017), p. 265-277
doi: 10.1107/S1600576716020604

Farajian, M.; Hardenacke, V.; Pfeiffer, W.; Klaus, M.; Kornmeier, J.R.: Numerical and experimental investigations on shot-peened high-strength steel by means of hole drilling, X-ray, synchrotron and neutron diffraction analysis. , Materials Testing 59 (2017), p. 161-165
doi: 10.3139/120.110978

Browne, D.J.; García-Moreno, F.; Nguyen-Thi, H.; Zimmermann, G.; Kargl, L.; Mathiesen, R.H.; Griesche, A.; Minster, O.: Overview of In Situ X-Ray Studies of Light Alloy Solidification in Microgravity. , In: Solanki, Kiran ... [Ed.] : Magnesium Technology 2017. Cham: Springer, 2017. - ISBN 978-3-319-52391-0, p. 581-590
doi: 10.1007/978-3-319-52392-7_80

Genzel, C.; Klaus, M.: Residual Stress Analysis by Energy-Dispersive Synchrotron X-ray Diffraction. , In: Peter Staron ... [Ed.] : Neutrons and Synchrotron Radiation in Engineering Materials Science : From Fundamentals to Applications: Second Edition. Weinheim: Wiley, 2017. - ISBN 978-3-527-33592-3, p. 161-177
doi: 10.1002/9783527684489.ch9

Klaus, M.; Genzel, C.: Residual Stresses in Thin Films and Coated Tools: Challenges and Strategies for Their Nondestructive Analysis by X-ray Diffraction Methods. , In: Peter Staron ... [Ed.] : Neutrons and Synchrotron Radiation in Engineering Materials Science : From Fundamentals to Applications: Second Edition. Weinheim: Wiley, 2017. - ISBN 978-3-527-33592-3, p. 439-449
doi: 10.1002/9783527684489.ch24

Sun, F.; Moroni, R.; Dong, K.; Markötter, H.; Zhou, D.; Hilger, A.; Zielke, L.; Zengerle, R.; Thiele, S.; Banhart, J.; Manke, I.: Study of the Mechanisms of Internal Short Circuit in a Li/Li Cell by Synchrotron X-ray Phase Contrast Tomography. , ACS Energy Letters 2 (2017), p. 94-104
doi: 10.1021/acsenergylett.6b00589

Bartosik, M.; Holec, D.; Apel, D.; Klaus, M.; Genzel, Ch.; Keckes, J.; Arndt, M.; Polcik, P.; Koller, C.M.; Mayrhofer, P.H.: Thermal expansionof Ti-Al-N and Cr-Al-N coatings. , Scripta Materialia 127 (2017), p. 182-185
doi: 10.1016/j.scriptamat.2016.09.022

Biberger, Julian: Tribologisch induzierte Oberflächenveränderungen im Reib-Verschleiß-Kontakt Kolbenring gegen Zylinderlaufbahn. , Berlin, Technische Universität, Diss., 2017

2016

Send, S.; Abboud, A.; Wiesner, N.; Shokr, M.; Klaus, M.; Genzel, C.; Conka-Nurdan, T.; Schlosser, D.; Huth, M.; Hartmann, R.; Strüder, L.; Pietsch, U.: Application of a pnCCD for energy-dispersive Laue diffraction with ultra-hard X-rays. , Journal of Applied Crystallography 49 (2016), p. 222 - 233
doi: 10.1107/S1600576715023997

Escudero, J.; Notario, B.; Jimenez, C.; Rodriguez-Perez, M.A.: Characterization of nanoclay intercalation during foaming with in situ energy-dispersive X-ray diffraction. , Journal of Applied Polymer Science 133 (2016), p. 43432/1-9
doi: 10.1002/APP.43432

Stange, H.; Brunken, S.; Greiner, D.; Heinemann, M.-D.; Alexander, C.; Simon, S.; Bäcker, J.-P.; Klaus, M.; Genzel, C.; Mainz, R.: Diffusion-induced grain boundary migration as mechanism for grain growth and defect annihilation in chalcopyrite thin films. , Acta Materialia 111 (2016), p. 377-384
doi: 10.1016/j.actamat.2016.03.073

Garces, G.; Mathis, K.; Perez, P.; Capek, J.; Adeva, P.: Effect of reinforcing shape on twinning in extruded magnesium matrix composites. , Materials Science and Engineering A 666 (2016), p. 48-53
doi: 10.1016/j.msea.2016.04.028

Götze, L.C.; Milke, R.; Zizak, I.; Wirth, R.: In situ monitoring and ex situ TEM analyses of spinel (MgAl2O4) growth between (111)-oriented periclase (MgO) substrates and Al2O3 thin films. , Journal of Materials Science 51 (2016), p. 8824-8844
doi: 10.1007/s10853-016-0130-2

Pistor, P.; Mainz, R.; Heinemann, M.D.; Unold, T.; Scheer, R.: In Situ Real-Time Characterization of Thin-Film Growth. , In: In situ real-time characterization of thin-film growth. Weinheim: Wiley, 2016. - ISBN 978-3-527-41003-3, p. 441-468
doi: 10.1002/9783527699025.ch16

Platt, P.; Lunt, D.; Polatidis, E.; Wenman, M.R.; Preuss, M.: In-situ digital image correlation for fracture analysis of oxides formed on zirconium alloys. , Corrosion Science 111 (2016), p. 344-351
doi: 10.1016/j.corsci.2016.05.026

García, J.; Pinto, H.; Ramos, E.; Espinoza, C.; Östby, J.; Coelho, R.: In-situ high temperature stress analysis of Ti(C,N) coatings on functionally graded cemented carbides by energy dispersive synchrotron X-ray diffraction. , International Journal of Refractory Metals and Hard Materials 56 (2016), p. 27 - 34
doi: 10.1016/j.ijrmhm.2015.12.001

Hemmesi, K.; Farajian, M.; Siegele, D.: Numerical and experimental description of the welding residual stress field in tubular joints for fatigue assessment. , Welding in the World 60 (2016), p. 741-748
doi: 10.1007/s40194-016-0328-6

Brito, P.; Pinto, H.; Kostka, A.: The crystallographic template effect assisting the formation of stable α-Al2O3 during low temperature oxidation of Fe-Al alloys. , Corrosion Science 105 (2016), p. 100-108
doi: 10.1016/j.corsci.2016.01.007

Lieblich, M.; Barriuso, S.; Multigner, M.; González-Doncel, G.; Gonzalez-Carrasco, J.L.: Thermal oxidation of medical Ti6Al4V blasted with ceramic particles: effects on the microstructure, residual stresses and mechanical properties. , Corrosion Science 63 (2016), p. 390 - 398
doi: 10.1016/j.jmbbm.2016.07.011

2015

Sticchi, M.; Staron, P.; Meixner, M.; Klaus, M.; Rebelo-Kornmeier, J.; Huber, N.; Kashaev, N.: A parametric study of laser spot size and coverage on the laser shock peening induced residual stress in thin aluminium samples. , The Journal of Engineering (2015), p. 1-9
doi: 10.1049/joe.2015.0106

Platt, P.; Polatidis, E.; Frankel, P.; Klaus, M.; Gass, M.; Howells, R.; Preuss, M.: A Study into Stress Relaxation in Oxides Formed on Zirconium Alloys. , Journal of Nuclear Materials 456 (2015), p. 415-425
doi: 10.1016/j.jnucmat.2014.09.072

Uhlmann, E.; Sammler, F.; Meixner, M.; Heinrich, D.; Gansert, F.; Reimers, W.; Berger, D.; Rieck, I.: Analysis of residual stresses and wear mechanism of HF-CVD diamond coated cemetend carbide tools. , Production Engineering : Research and Developement 9 (2015), p. 99-107
doi: 10.1007/s11740-014-0580-9

Lentz, Martin Christoph: Deformation behavior of extruded magnesium alloys ME21, WE54, L4 and LA41. , Berlin, Technische Universität, Diss., 2015

Meixner, M.; Fuss, T.; Klaus, M.; Genzel, C.: Diffraction analysis of strongly inhomogeneous residual stress depth distributions by modification of the stress scanning method - I. Theoretical concept. , Journal of Applied Crystallography 48 (2015), p. 1451-1461
doi: 10.1107/S160057671501448X

Meixner, M.; Fuss, T.; Klaus, M.; Genzel, M.; Genzel, C.: Diffraction analysis of strongly inhomogeneous residual stress depth distributions by modification of the stress scanning method - II. Experimental implementation. , Journal of Applied Crystallography 48 (2015), p. 1462 - 1475
doi: 10.1107/S160057671501585X

Lentz, M.; Klaus, M.; Wagner, M.; Fahrenson, Ch.; Beyerlein, I. J.; Zecevic, M.; Reimers, W.; Knezevic, M.: Effect of age hardening on the deformation behavior of an Mg-Y-Nd alloy: In-situ X-ray diffraction and crystal plasticity modeling. , Materials Science and Engineering A 628 (2015), p. 396-409
doi: 10.1016/j.msea.2015.01.069

Gibson, J.L.; Jimenez, C.; Garcia De Andres, C.; Danon, C.A.; Luppo, M.I.: Evaluation of the Abnormal Grain Growth in an ASTM 213 Grade T91 Steel. , Procedia Materials Science 8 (2015), p. 1118-1126
doi: 10.1016/j.mspro.2015.04.175

Witte, W.; Abou-Ras, D.; Albe, K.; Bauer, G.H.; Bertram, F.; Boit, C.; Brueggemann, R.; Christen, J.; Dietrich, J.; Eicke, A.; Hariskos, D.; Maiberg, M.; Mainz, R.; Meessen, M.; Mueller, M.; Neumann, O.; Orgis, T.; Paetel, S.; Pohl, J.; Rodriguez Alvarez, H.; Scheer, R.; Schock, H.-W.; Unold, T.; Weber, A.; Powalla, M.: Gallium gradients in Cu(In,Ga)Se2 thin-film solar cells. , Progress in Photovoltaics 23 (2015), p. 717–733
doi: 10.1002/pip.2485

Scherg-Kurmes, H.; Körner, S.; Ring, S.; Klaus, M.; Korte, L.; Ruske, F.; Schlatmann, R.; Rech, B.; Szyszka, B.: High mobility In2O3:H as contact layer for a-Si:H/c-Si heterojunction and muc-Si:H thin film solar cells. , Thin Solid Films 594 (2015), p. 316-322
doi: 10.1016/j.tsf.2015.03.022

Dabah, Eitan: Hydrogen Interaction with Supermartensitic Stainless Steel studied by Energy Dispersive X-Ray Diffraction. , Magdeburg, Universität, Diss., 2015

Lentz, M.; Klaus, M.; Beyerlein, I.J.; Zecevic, M.; Reimers, W.; Knecevic, M.: In Situ X-Ray Diffraction and Crystal Plasticity Modeling of the Deformation Behavior of Extruded Mg-Li-(Al) Alloys: An Uncommon Tension-Compression Asymmetry. , Acta Materialia 86 (2015), p. 254-268
doi: 10.1016/j.actamat.2014.12.003

Shokr, Mohammad: PnCCD response to hard x-ray radiation. , Siegen, Universität, Master, 2015

Abboud, Ali: Polychromatic X-ray diffraction using a pnCCD : applications for material science. , Siegen, Universität, Diss., 2015

Kühnapfel, S.; Nickel, N.H.; Gall, S.; Klaus, M.; Genzel, C.; Rech, B.; Amkreutz, D.: Preferential {100} grain orientation in 10 micrometer-thick laser crystallized multicrystalline silicon on glass. , Thin Solid Films 576 (2015), p. 68-74
doi: 10.1016/j.tsf.2015.01.006

Zellmeier, M.; Rappich, J.; Klaus, M.; Genzel, C.; Janietz, S.; Frisch, J.; Koch, N.; Nickel, N.: Side chain engineering of poly-thiophene and its impact on crystalline silicon based hybrid solar cells. , Applied Physics Letters 107 (2015), p. 203301/1-4
doi: 10.1063/1.4935751

Carter, N.J.; Mainz, R.; Walker, B.C.; Hages, C.J.; Just, J.; Klaus, M.; Schmidt, S.S.; Weber, A.; Yang, W.-C.D.; Zander, O.; Stach, E.A.; Unold, T.; Agrawal, R.: The role of interparticle heterogeneities in the selenization pathway of Cu-Zn-Sn-S nanoparticle thin films: a real-time study. , Journal of Materials Chemistry C 3 (2015), p. 7128-7134
doi: 10.1039/c5tc01139f

Mainz, R.; Weber, A.; Rodriguez-Alvarez, H.; Levcenko, S.; Klaus, M.; Pistor, P.; Klenk, R.; Schock, H.-W.: Time-resolved investigation of Cu(In,Ga)Se2 growth and Ga gradient formation during fast selenization of metallic precursors. , Progress in Photovoltaics 23 (2015), p. 1131–1143
doi: 10.1002/pip.2531

2014

Coelho, R.S.; Klaus, M.; Genzel, Ch.: Analysis of Texture Depth Distribution by Energy-Dispersive Diffraction. , Materials Science Forum 768-769 (2014), p. 36-43
doi: 10.4028/www.scientific.net/MSF.768-769.36

Lentz, M.; Klaus, M.; Coelho, R.S.; Schäfer, N.; Schmack, F.; Reimers, W.; Clausen, B.: Analysis of the Deformation Behavior of Magnesium-Rare Earth Alloys Mg-2 pct Mn-1 pct Rare Earth and Mg-5 pct Y-4 pct Rare Earth by In Situ Energy-Dispersive X-Ray Synchrotron Diffraction and Elasto-Plastic Self-Consistent Modeling. , Metallurgical and Materials Transactions A 45A (2014), p. 5721-5735
doi: 10.1007/s11661-014-2533-5

Farajian, M.; Hardenacke, V.; Preussner, J.; Pfeiffer, W.; Siegele, D.: Description of the Surface and Subsurface Material Conditions after Applying High Frequency Mechanical Impact (HFMI) Treatment, Shot Peening and Deep Rolling: A Step Towards Surface Engineering in Fatigue Resistant Welds. , In: International Institute of Welding, IIW [Ed.] : Commission XIII Fatigue of welded components and structures : XIII-2532-14. Roissy Ch. De Gaulle Cedex, 2014, p. 1-11

Meixner, Matthias: Entwicklung von Mess- und Auswertestrategien zur ortsaufgelösten Analyse oberflächennaher Eigenspannungstiefengradienten. , Berlin, Technische Universität, Diss., 2014

Kriska, M.; Tacq, J.; Van Acker, K.; Seefeldt, M.: Evolution of residual micro phase and orientation dependent stresses during cold wire drawing. , In: S.J.B Kurz ... [Ed.] : International Conference on Residual Stresses 9 (ICRS 9) : Garmisch-Partenkirchen; Germany; 7 October 2012 through 9 October 2012. Zürich: Trans Tech Publ., 2014 (Materials Science Forum ; 768-769). - ISBN 978-3-03785-849-3, p. 327-334
doi: 10.4028/www.scientific.net/MSF.768-769.327

Kromm, A.; Steppan, E.; Kannengiesser, T.: High-Energy Synchrotron Study of the Stress–Strain Behavior of Hydrogen-Charged High Strength Structural Steel. , In: Kannengiesser, Th. ... [Ed.] : In-situ Studies with Photons, Neutrons and Electrons Scattering II. Springer, 2014. - ISBN 978-3-319-06145-0, p. 165-176
doi: 10.1007/978-3-319-06145-0_10

Dabah, E.; Kannengiesser, T.; Eliezer, D.; Boellinghaus, T.: Hydrogen Interaction with Residual Stresses in Steel Studied by Synchrotron X-Ray Diffraction. , In: Brokmeier, Heinz-Günter [Ed.] : Mechanical stress evaluation by neutrons and synchrotron radiation VI : selected, peer reviewed papers from the 6th International Conference on Mechanical Stress Evaluation by Neutrons and Synchrotron Radiation (MECA SENS VI 2011), September 7-9, 2011, Hamburg, Germany. Durnten-Zurich: Trans Tech Publ., 2014 (Materials science forum ; 772). - ISBN 978-3-03785-911-7, p. 91-95
doi: 10.4028/www.scientific.net/MSF.772.91

Workowski, M.; Nitschke-Pagel, T.; Dilger, K.: Identification of load induced inhomogeneous plastic deformations in aluminium welds by diffraction methods. , In: S.J.B Kurz ... [Ed.] : International Conference on Residual Stresses 9 (ICRS 9) : Garmisch-Partenkirchen; Germany; 7 October 2012 through 9 October 2012. Zürich: Trans Tech Publ., 2014 (Materials Science Forum ; 768-769). - ISBN 978-3-03785-849-3, p. 675-681
doi: 10.4028/www.scientific.net/MSF.768-769.675

Ramos-Moore, E.; Espinoza, C.; Coelho, R.S.; Pinto, H.; Brito, P.; Soldera, F.; Mücklich, F.; Garcia, J.: Investigations on Thermal Stresses of a Graded Ti(C,N) Coating Deposited on WC-Co Hardmetal. , Advanced Materials Research 996 (2014), p. 848-854
doi: 10.4028/www.scientific.net/AMR.996.848

Stefenelli, M.; Riedl, A.; Todt, J.; Bartosik, M.; Daniel, R.; Mitterer, C.; Keckes, J.: Macroscopic Fracture Behaviour of CrN Hard Coatings Evaluated by X-Ray Diffraction Coupled with Four-Point Bending. , In: S.J.B Kurz ... [Ed.] : International Conference on Residual Stresses 9 (ICRS 9) : Garmisch-Partenkirchen; Germany; 7 October 2012 through 9 October 2012. Zürich: Trans Tech Publ., 2014 (Materials Science Forum ; 768-769). - ISBN 978-3-03785-849-3, p. 272-279
doi: 10.4028/www.scientific.net/MSF.768-769.272

Silva, E.P.; Batista, L.F.; Callegari, B.; Ferrinho, V.; Buzolin, R.H.; Coelho, R.S.; Warchomicka, F.; Requena, G.C.; Ramirez, A.J.; Pinto, H.: Microstructure and Residual Stress Formation during Friction-Stir Welding of Semi-Solid ZK60 Magnesium Alloy. , Advanced Materials Research 922 (2014), p. 688-693
doi: 10.4028/www.scientific.net/AMR.922.688

Bachmaier, A.; Rathmayr, G.B.; Bartosik, M.; Apel, D.; Zhang, Z.; Pippan, R.: New insights on the formation of supersaturated solid solutions in the Cu-Cr system deformed by high-pressure torsion. , Acta Materialia 69 (2014), p. 301-313
doi: 10.1016/j.actamat.2014.02.003

Maawad, E.; Brokmeier, H.-G.; Wagner, L.; Hofmann, M.; Gan, W.M.; Genzel, Ch.; Klaus, M.: Non-destructive residual stress evaluation in mechanically surface treated Ti-2.5Cu by diffraction techniques. , NDT & E International 61 (2014), p. 67-70
doi: 10.1016/j.ndteint.2013.10.002

Farajian, M.; Hardenacke, V.; Klaus, M.; Schweizer, F.; Pfeiffer, W.; Siegele, D.: Numerical Studies of Shot Peening of High Strength Steels and the related Experimental Investigations by means of Hole Drilling, X-ray and Synchrotron Diffraction Analysis. , In: International Conference on Shot Peening ICSP12 : Goslar, Germany, September 15-18, 2014. , 2014, p. 317-323

Mainz, R.; Singh, A.; Levcenko, S.; Klaus, M.; Genzel, C.; Ryan, K.M.; Unold, T.: Phase-transition-driven growth of compound semiconductor crystals from ordered met-astable nanorods. , Nature Communications 5 (2014), p. 3133
doi: 10.1038/ncomms4133

Fuß, T.; Meixner, M.; Klaus, M.; Genzel, Ch.: Residual Stress Analysis by Energy-Dispersive Synchrotron Diffraction: Concepts for High Resolution Depth Profiling in Real Space. , Materials Science Forum 768-769 (2014), p. 44-51
doi: 10.4028/www.scientific.net/MSF.768-769.44

Genzel, Ch.; Apel, D.; Klaus, M.; Genzel, M.; Balzar, D.: Residual Stress Gradient Analysis by Multiple Diffraction Line Methods. , Materials Science Forum 768-769 (2014), p. 3-18
doi: 10.4028/www.scientific.net/MSF.768-769.3

Schlosser, Dieter Michael: Response of high resolution silicon photodetectors coupled to CsI(Tl) or LaBr3(Ce). , Siegen, Universität, Diss., 2014

Apel, D.; Klaus, M.; Genzel, M.; Genzel, Ch.: Rietveld-based energy-dispersive residual stress evaluation: analysis of complex stress fields σij(z). , Journal of Applied Crystallography 47 (2014), p. 511-526
doi: 10.1107/S1600576713034158

Workowski, M.; Nitschke-Pagel, T.; Dilger, K.: Stress measurement at loaded aluminium welds using diffraction methods. , Advanced Materials Research 996 (2014), p. 431-438
doi: 10.4028/www.scientific.net/AMR.996.431

Tacq, J.; Kriska, M.; Seefeldt, M.: Synchrotron diffraction study of the cementite phase in cold drawn pearlitic steel wires. , In: S.J.B Kurz ... [Ed.] : International Conference on Residual Stresses 9 (ICRS 9) : Garmisch-Partenkirchen; Germany; 7 October 2012 through 9 October 2012. Zürich: Trans Tech Publ., 2014 (Materials Science Forum ; 768-769). - ISBN 978-3-03785-849-3, p. 380-387
doi: 10.4028/www.scientific.net/MSF.768-769.380

Brauser, S.; Kromm, A.; Dabah, E.; Kannengiesser, T.; Rethmeier, M.: Thermal stability of retained austenite in low alloyed TRIP-steel determined by high energy synchrotron radiation. , Materials Science Forum 772 (2014), p. 129-133
doi: 10.4028/www.scientific.net/MSF.772.129

2013

Kaufmann, C.A.; Greiner, D.; Rodriguez-Alvarez, H.; Weber, A.; Heinemann, M.D.; Lauche, J.; Klaus, M.; Genzel, C.; Schock, H.W.; Mainz, R.: Co-evaporation of Cu(In,Ga)Se2 at Low Temperatures: an In-Situ X-Ray Growth Analysis. , In: 39th Photovoltaic Specialists Conference (PVSC), 2013. IEEE, 2013. - ISBN 978-1-4799-3299-3, p. 3058-3061

Jegou, S.; Christiansen, T.L.; Klaus, M.; Genzel, Ch.; Somers, M.A.J.: Determination of composition, residual stress and stacking fault depth profiles in expanded austenite with energy-dispersive diffraction. , Thin Solid Films 530 (2013), p. 71-76
doi: 10.1016/j.tsf.2012.06.029

Lentz, M.; Klaus, M.; Reimers, W.; Clausen, B.: Effect of high temperature heat treatments on the deformation behavior of Mg-2%Mn-0.7%Ce extrusions investigated by in-situ energy-dispersive synchrotron X-ray diffraction and elasto-plastic self-consistent modeling. , Materials Science and Engineering A 586 (2013), p. 178-189
doi: 10.1016/j.msea.2013.08.020

Rodriguez-Alvarez, H.; Weber, A.; Lauche, J.; Kaufmann, Ch.A.; Rissom, T.; Greiner, D.; Klaus, M.; Unold, Th.; Genzel, C.; Schock, H.-W.; Mainz, R.: Formation of CuInSe2 and CuGaSe2 thin films deposited by three-stage thermal co-evaporation: a real-time x-ray diffraction and fluorescence study. , Advanced Energy Materials 3 (2013), p. 1381-1387
doi: 10.1002/aenm.201300339

Jiménez, C.; García-Moreno, F.; Pfretzschner, B.; Kamm, P.H.; Neu, T.R.; Klaus, M.; Genzel, C.; Hilger, A.; Manke, I.; Banhart, J.: Metal foaming studied in situ by energy dispersive X-ray diffraction of synchrotron radiation, X-ray radioscopy and optical expandometry. , Advanced Engineering Materials 15 (2013), p. 141-148
doi: 10.1002/adem.201200183

Mogni, L.; Prado, F.; Jiménez, C.; Caneiro, A.: Oxygen order-disorder phase transition in layered GdBaCo2O5+δ perovskite: thermodynamic and transport properties. , Solid State Ionics 240 (2013), p. 19-28
doi: 10.1016/j.ssi.2013.03.021

Mainz, R.; Walker, B.C.; Schmidt, S.S.; Zander, O.; Weber, A.; Rodriguez-Alvarez, H.; Just, J.; Klaus, M.; Agrawal, R.; Unold, T.: Real-time observation of Cu2ZnSn(S,Se)4 solar cell absorber layer formation from nanoparticle precursors. , Physical Chemistry Chemical Physics 15 (2013), p. 18281-18289
doi: 10.1039/c3cp53373e

Rodriguez-Alvarez, H.; Weber, A.; Mainz, R.; Klaus, M.; Kaufmann, C.A.; Rissom, T.; Genzel, C.; Schock, H.-W.: Real-time observation of the phase transformations and microstructural changes during the incorporation of In into a Cu thin film at 770K. , Journal of Alloys and Compounds 588 (2013), p. 644-647
doi: 10.1016/j.jallcom.2013.11.147

Rodriguez-Alvarez, H.; Mainz, R.; Caballero, R.; Abou-Ras, D.; Klaus, M.; Gledhill, S.; Weber, A.; Kaufmann, C.A.; Schock, H.-W.: Real-time study of Ga diffusion processes during the formation of Cu(In,Ga)Se2: The role of Cu and Na content. , Solar Energy Materials and Solar Cells 116 (2013), p. 102-109
doi: 10.1016/j.solmat.2013.04.008

Rodriguez-Alvarez, H.; Barreau, N.; Kaufmann, C.A.; Weber, A.; Klaus, M.; Painchaud, T.; Schock, H.-W.; Mainz, R.: Recrystallization of Cu(In,Ga)Se2 thin films studied by X-ray diffraction. , Acta Materialia 61 (2013), p. 4347-4353
doi: 10.1016/j.actamat.2013.04.006

Genzel, C.; Denks, I.A.; Klaus, M.: Residual Stress Analysis by X-Ray Diffraction Methods in Modern Diffraction Methods. , In: Modern Diffracztion Methods. WILEY-VCH, 2013. - ISBN 978-3-527-32279-4, p. 127-153

Meixner, M.; Klaus, M.; Genzel, Ch.; Reimers, W.: Residual stress analysis of diamond-coated WC-Co cutting tools: separation of film and substrate information by grazing X-ray diffraction. , Journal of Applied Crystallography 46 (2013), p. 1323-1330
doi: 10.1107/S0021889813020451

Polatidis, E.; Frankel, P.; Wei, J.; Klaus, M.; Comstock, R.J.; Ambard, A.; Lyon, S.; Cottis, R.A.; Preuss, M.: Residual stresses and tetragonal phase fraction characterization of corrosion tested Zircaloy-4 using energy dispersive synchrotron X-Ray diffraction. , Journal of Nuclear Materials 432 (2013), p. 102-112
doi: 10.1016/j.jnucmat.2012.07.025

Mainz, R.; Pistor, P.; Schmidt, S.; Klaer, J.; Klenk, R.: Schlussbericht: “HT-CIGS, Entwicklung von Cu(In,Ga)S2-Dünnschichtsolarmodulen“. , 2013

Rodriguez-Alvarez, H.; Mainz, R.: Schlussbericht: “Verbundprojekt GRACIS: Chemische Gradienten in Cu(In,Ga)(S,Se)2 : Insitu-Diagnostik“. , 2013

Meixner, M.; Klaus, M.; Genzel, Ch.: Sin2ψ-based residual stress gradient analysis by energy-dispersive synchrotron diffraction constrained by small gauge volumes. I. Theoretical concept. , Journal of Applied Crystallography 46 (2013), p. 610 - 618
doi: 10.1107/S0021889813008340

Meixner, M.; Klaus, M.; Genzel, Ch.: Sin2ψ-based residual stress gradient analysis by energy-dispersive synchrotron diffraction constrained by small gauge volumes. II. Experimental implementation. , Journal of Applied Crystallography 46 (2013), p. 619 - 627
doi: 10.1107/S0021889813008364

Abboud, A.; Send, S.; Pashniak, N.; Leitenberger, W.; Ihle, S.; Huth, M.; Hartmann, R.; Strueder, L.; Pietsch, U.: Sub-pixel resolution of a pnCCD for X-ray white beam applications. , Journal of Instrumentation 8 (2013), p. P05005/1-15
doi: 10.1088/1748-0221/8/05/P05005

Wei, J.; Frankel, P.; Polatidis, E.; Blat, M.; Ambard, A.; Comstock, R.J.; Hallstadius, L.; Hudson, D.; Smith, G D.W.; Grovenor, C.R M.; Klaus, M.; Cottis, R.A.; Lyon, S.; Preuss, M.: The effect of Sn on autoclave corrosion performance and corrosion mechanisms in Zr-Sn-Nb alloys. , Acta Materialia 61 (2013), p. 4200-4214
doi: 10.1016/j.actamat.2013.03.046

Apel, Daniel: Tiefenaufgelöste Analyse randschichtnaher Struktur- und Eigenschaftsgradienten in vielkristallinen Werkstoffen mittels energiedispersiver Röntgenbeugung. , Berlin, Technische Universität, Diss., 2013

Send, Sebastian: Utilization of a frame-store pnCCD for energy-dispersive Laue diffraction with white synchrotron radiation. , Siegen, Universität, Diss., 2013

Farajian, M.: Welding residual stress behavior under mechanical loading. , Welding in the World 57 (2013), p. 157-169
doi: 10.1007/s40194-013-0024-8

Garcia-Moreno, F.; Jimenez, C.; Kamm, P.H.; Klaus, M.; Wagener, G.; Banhart, J.; Genzel, Ch.: White-beam X-ray radioscopy and tomography with simultaneous diffraction at the EDDI beamline. , Journal of Synchrotron Radiation 20 (2013), p. 809-810
doi: 10.1107/S0909049513018670

2012

Brito, P.; Pinto, H.; Genzel, Ch.; Klaus, M.; Kaysser-Pyzalla, A.: Epitaxial stress and texture in thin oxide layers grown on Fe-Al alloys. , Acta Materialia 60 (2012), p. 1230-1237
doi: 10.1016/j.actamat.2011.11.033

Kromm, A.: Henry Granjon Prize Competition 2011 : Winner Category B: "Materials Behaviour and Weldability" : Exploring the Interaction of Phase Transformation and Residual Stress During Welding by Synchrotron Diffraction. , Welding in the World 56 (2012), p. 2-11
doi: 10.1007/BF03321375

Zumsande, K.; Krasokha, N.; Huth, S.; Weber, S.; Theisen, W.: In situ investigation of the gas–solid interaction between highalloyed steel powder and nitrogen by energy dispersive diffraction. , Journal of Materials Science 47 (2012), p. 3214-3226
doi: 10.1007/s10853-011-6159-3

Dabah, E.; Kannengiesser, T.; Eliezer, D.; Boellinghaus, T.: In situ synchrotron X-ray radiation analysis of hydrogen behavior in stainless steel subjected to continuous heating. , Journal of Materials Science 47 (2012), p. 5879-5885
doi: 10.1007/s10853-012-6489-9

Garcés, G.; Onorbe, E.; Pérez, P.; Klaus, M.; Genzel, C.; Adeva, P.: Influence of SiC particles on compressive deformation of magnesium matrix composites. , Materials Science and Engineering A 533 (2012), p. 119-123
doi: 10.1016/j.msea.2011.10.103

Roy, S.; Gibmeier, J.; Kostov, V.; Weidenmann, K.A.; Nagel, A.; Wanner, A.: Internal load transfer and damage evolution in a 3D interpenetrating metal/ceramic composite. , Materials Science and Engineering A 551 (2012), p. 272-279
doi: 10.1016/j.msea.2012.05.016

Maawad, E.; Sano, Y.; Wagner, L.; Brokmeier, H.-G.; Genzel, Ch.: Investigation of laser shock peening effects on residual stress state and fatigue performance of titanium alloys. , Materials Science and Engineering A 536 (2012), p. 82-91
doi: 10.1016/j.msea.2011.12.072

Ferreira-Barragans, S.; Fernandez, R.; Fernandez-Castrillo, P.; Gonzalez-Doncel, G.: Kinetics of tri-axial and spatial residual stress relaxation: Study by synchrotron radiation diffraction in a 2014Al alloy. , Journal of Alloys and Compounds 523 (2012), p. 94-101
doi: 10.1016/j.jallcom.2012.01.081

Bartosik, M.; Daniel, R.; Zhang, Z.; Deluca, M.; Ecker, W.; Stefenelli, M.; Klaus, M.; Genzel, C.; Mitterer, C.; Keckes, J.: Lateral gradients of phases, residual stresses and hardness in a laser heated Ti0.52Al0.48N coating on hard metal. , Surface & Coatings Technology 206 (2012), p. 4502-4510
doi: 10.1016/j.surfcoat.2012.02.035

Villa, M.; Grumsen, F.B.; Pantleon, K.; Somers, M.A.J.: Martensitic transformation and stress partitioning in a high-carbon steel. , Scripta Materialia 67 (2012), p. 621-624
doi: 10.1016/j.scriptamat.2012.06.027

Jimenez, C.; Garcia-Moreno, F.; Pfretzschner, B.; Kamm, P.; Neu, T.; Klaus, M.; Genzel, Ch.; Hilger, A.; Manke, I.; Banhart, J.: Metal foaming studied in-situ by energy dispersive XRD of synchrotron radiation, X-ray radioscopy, and optical imaging. , In: Porous metals and metallic foams : MetFoam 2011 : proceedings of the 7th International Conference on Porous Metals and Metallic Foams, held in Busan, Korea, September 18-21, 2011. Seoul, Korea: GSIntervision, 2012, p. 13-19

Jimenez, C.; Garcia-Moreno, F.; Rack, A.; Tucoulou, R.; Klaus, M.; Pfretzschner, B.; Rack, T.; Cloetens, P.; Banhart, J.: Partial decomposition of TiH2 studied in situ by energy-dispersive diffraction and ex situ by diffraction microtomography of hard X-ray synchrotron radiation. , Scripta Materialia 66 (2012), p. 757-760
doi: 10.1016/j.scriptamat.2012.01.057

Schorr, S.; Mainz, R.; Moenig, H.; Lauermann, I.; Bär, M.: The complex material properties of chalcopyrite and kesterite thin-film solar cell absorbers tackled by synchrotron-based analytics. , Progress in Photovoltaics 20 (2012), p. 557-567
doi: 10.1002/pip.1256

2011

Huppmann, Michael: Charakterisierung der Verformungsmechanismen der stranggepressten Magnesiumlegierungen AZ31 und ME21 unter monotoner und zyklischer Belastung. , Berlin, Technische Universität, Diss., 2011

Huppmann, Michael: Charakterisierung der Verformungsmechanismen der stranggepressten Magnesiumlegierungen AZ31 und ME21 unter monotoner und zyklischer Belastung = Characterization of deformation mechanisms of the hot extruded magnesium alloys AZ31 and ME21 under monotonic and cyclic loading conditions. , Berlin, Technische Universität, Diss., 2011

Jimenez, C.; Garcia-Moreno, F.; Pfretzschner, B.; Klaus, M.; Wollgarten, M.; Zizak, I.; Schumacher, G.; Tovar, M.; Banhart, J.: Decomposition of TiH2 studied in situ by synchrotron X-ray and neutron diffraction. , Acta Materialia 59 (2011), p. 6318-6330
doi: 10.1016/j.actamat.2011.06.042

Zhilyaev, A.P.; Sabirov, I.; Gonzalez-Doncel, G.; Molina-Aldareguia, J.; Srinivasarao, B.; Perez-Prado, M.T.: Effect of Nb additions on the microstructure, thermal stability and mechanical behavior of high pressure Zr phases under ambient conditions. , Materials Science and Engineering A 528 (2011), p. 3496-3505
doi: 10.1016/j.msea.2011.01.062

Genzel, Ch.; Krahmer, S.; Klaus, M.; Denks, I.A.: Energy-Dispersive Diffraction Stress Analysis under Laboratory and Synchrotron Conditions: a Comparative Study. , Journal of Applied Crystallography 44 (2011), p. 1-12
doi: 10.1107/S0021889810047898

Rissom, T.; Mainz, R.; Kaufmann, C.A.; Caballero, R.; Efimova, V.; Hoffmann, V.; Schock, H.-W.: Examination of growth kinetics of copper rich Cu(In,Ga)Se-2-films using synchrotron energy dispersive X-ray diffractometry. , Solar Energy Materials and Solar Cells 95 (2011), p. 250-253
doi: 10.1016/j.solmat.2010.05.007

Genzel, C.; Denks, I.A.; Coelho, R.; Thomas, D.; Mainz, R.; Apel, D.; Klaus, M.: Exploiting the features of energy-dispersive synchrotron diffraction for advanced residual stress and texture analysis. , Journal of Strain Analysis for Engineering Design 46 (2011), p. 615-625
doi: 10.1177/0309324711403824

Kromm, A.; Brauser, S.; Kannengiesser, T.; Rethmeier, M.: High-energy synchrotron diffraction study of a transformation induced plasticity steel during tensile deformation. , Journal of Strain Analysis for Engineering Design 46 (2011), p. 581-591
doi: 10.1177/0309324711403969

Dabah, E.; Kannengiesser, Th.; Eliezer, D.; Boellinghaus, T.: In situ analysis of hydrogen behaviour in stainless steels by high energy synchrotron radiation. , Materials Science and Engineering A 528 (2011), p. 1608-1614
doi: 10.1016/j.msea.2010.10.090

Thomas, D.; Mainz, R.; Rodriguez-Alvarez, H.; Marsen, B.; Abou-Ras, D.; Klaus, M.; Genzel, C.; Schock, H.-W.: In-situ studies of the recrystallization process of CuInS2 thin films by energy dispersive X-ray diffraction. , Thin Solid Films 519 (2011), p. 7193-7196
doi: 10.1016/j.tsf.2010.12.229

Merdes, S.; Mainz, R.; Rodriguez-Alvarez, H.; Klaer, J.; Klenk, R.; Meeder, A.; Schock, H.-W.; Lux-Steiner, M.-C.: Influence of precursor stacking on the absorber growth in Cu(In,Ga)S2 based solar cells prepared by a rapid thermal process. , Thin Solid Films 519 (2011), p. 7189-7192
doi: 10.1016/j.tsf.2011.01.397

Vogli, E.; Tillmann, W.; Selvadurai-Lassl, U.; Fischer, G.; Herper, J.: Influence of Ti/TiAlN-multilayer designs on their residual stresses and mechanical properties. , Applied Surface Science 257 (2011), p. 8550-8557
doi: 10.1016/j.apsusc.2011.05.013

Roy, S.; Gibmeier, J.; Kostov, V.; Weidenmann, K.A.; Nagel, A.; Wanner, A.: Internal load transfer in a metal matrix composite with a three-dimensional interpenetrating structure. , Acta Materialia 59 (2011), p. 1424-1435
doi: 10.1016/j.actamat.2010.11.004

Meixner, M.; Fitzpatrick, M.E.; Reimers, W.: Measurement of the evolution of internal strain and load partitioning in magnesium hybrid composites under compression load using in-situ synchrotron X-ray diffraction analysis. , Composites Science and Technology 71 (2011), p. 167-176
doi: 10.1016/j.compscitech.2010.11.003

Schorr, S.; Stephan, C.; Mainz, R.; Rodriguez-Alvarez, H.; Tovar, M.: Neutrons and Photons in Materials Research for Thin Film Solar Cells. , Advanced Engineering Materials 13 (2011), p. 737-741
doi: 10.1002/adem.201000290

Maawad, E.; Brokmeier, H.-G.; Wagner, L.; Genzel, Ch.; Klaus, M.: Residual Stress Distribution in Alpha and Beta Phases of Mechanically Surface Treated TIMETAL LCB Determined by Energy-Dispersive X-Ray Diffraction. , In: Proceedings of the 11th Int. Conf. on Shot Peening (2011). , 2011, p. 1-6

Schöbel, Michael: Residual Stresses and Thermal Fatigue in Metal Matrix Composites: A comparative study of stress measurements by neutron and synchrotron diffraction combined with tomography. , TU Vienna, Austria, 2011

Kromm, A.; Kannengiesser, T.; Altenkirch, J.; Gibmeier, J.: Residual Stresses in Multilayer Welds with Different Martensitic Transformation Temperatures Analyzed by High-Energy Synchrotron Diffraction. , Materials Science Forum 681 (2011), p. 37-42
doi: 10.4028/www.scientific.net/MSF.681.37

Apel, D.; Klaus, M.; Genzel, Ch.; Balzar, D.: Rietveld refinement of energy-dispersive synchrotron measurements. , Zeitschrift für Kristallographie 226 (2011), p. 934 - 943
doi: 10.1524/zkri.2011.1436

Farajian, Majid: Stability and Relaxation of Welding Residual Stresses. , Braunschweig, Techn. Univ., Diss., 2011

Bar, R.; Dabah, E.; Eliezer, D.; Kannengiesser, Th.; Boellinghaus, Th.: The Influence of Hydrogen on Thermal Desorption Processes in Structural Materials. , Procedia Engineering 10 (2011), p. 3668-3676
doi: 10.1016/j.proeng.2011.04.604

Kromm, Arne: Umwandlungsverhalten und Eigenspannungen beim Schweißen neuartiger LTT-Zusatzwerkstoffe. , Otto-von-Guericke-Universität Magdeburg, 2011

2010

Jímenez, Catalina Elena: Characterization and Modification of Powders Used to Make Al-Based Metal Foams = Charakterisierung und Modifizierung von Pulvern zur Herstellung von Metallschäumen auf Aluminium-Basis. , TU Berlin, 2010

Jimenez, Catalina Elena: Characterization and modification of powders used to make aluminium-based metal foams. , Berlin, Technische Universität, Diss., 2010

Rodriguez-Alvarez, H.; Mainz, R.; Marsen, B.; Weber, A.; Schock, H. W.: Copper Sulfide Assisted Recrystallization of Cu-Poor CuInS2 Observed 'In-Situ' by Polychromatic X-ray Diffraction. , In: Akira Yamada ... [Ed.] : Thin-film compound semiconductor photovoltaics - 2009 : Symposium held April 13 - 17, 2009, San Francisco, California, U.S.A.. Warrendale, Pa. : MRS, 2010 (Materials Research Society symposium proceedings : 1165). - ISBN 978-1-60511-138-4, p. 53-59

Huppmann, M.; Reimers, W.: Development of Twin Fractions and Microstresses of the Hot Extruded Magnesium Alloy AZ31 under Cyclic Loading Conditions. , In: Chandra, T. [Ed.] : THERMEC 2009, 6th International Conference on Processing & Manufacturing of Advanced Materials; Berlin, Germany, August 25 - 29, 2009 ; part 4. Stafa-Zuerich [u.a.]: Trans Tech Publ. , 2010 (Materials Science Forum ; 638-642), p. 2411-2416
doi: 10.4028/www.scientific.net/MSF.638-642.2411

Hesse, Raik: Entwicklung und Applikation von optischen Prozesssteuerungen und -kontrollen zur Herstellung von Chalkopyritschichten. , Berlin, Technische Universität, Diss., 2010

Kromm, A.; Kannengiesser, T.; Gibmeier, J.: In-Situ Observation of Phase Transformations during Welding of low Transformation Temperature Filler Material. , Materials Science Forum 638-642 (2010), p. 3769-3774
doi: 10.4028/www.scientific.net/MSF.638-642.3769

Brito, P.; Pinto, H.; Klaus, M.; Genzel, C.; Pyzalla, A.: Internal Stresses and Texture of Nano-Structured Alumina Scales Growing on Fe3Al Polycrystals. , Advances in X-Ray Analysis 53 (2010), p. 81-88

Huppmann, Michael; Stark, Sebastian; Reimers, Walter: Microstructural development of the hot extruded magnesium alloy AZ31 under cyclic testing conditions. , International Journal of Materials Research 101 (2010), p. 1441-1449
doi: 10.3139/146.110378

Paiva Brito, Pedro: Phase Development, Texture and Internal Stress Evolution during the Oxidation of Iron Aluminides. , Universität Bochum , 2010

Rodriguez-Alvarez, H.; Mainz, R.; Marsen, B.; Abou-Ras, D.; Schock, H.-W.: Recrystallization of Cu-In-S thin films studied in situ by energy-dispersive X-ray diffraction. , Journal of Applied Crystallography 43 (2010), p. 1053-1061
doi: 10.1107/S0021889810025860

Rodriguez-Alvarez, H.; Mainz, R.; Marsen, B.; Schock, H.-W.: Recrystallization of Cu-poor CuInS2 assisted by metallic Cu or Ag. , Journal of Solid State Chemistry 183 (2010), p. 803-806
doi: 10.1016/j.jssc.2010.01.023

Multigner, M.; Ferreira-Barragans, S.; Frutos, E.; Jaafar, M.; Ibanez, J.; Marin, P.; Perez-Prado, M.T.; Gonzalez-Doncel, G.; Asenjo, A.; Gonzalez-Carrasco, J.L.: Superficial severe plastic deformation of 316 LVM stainless steel through grit blasting: Effects on its microstructure and subsurface mechanical properties. , Surface & Coatings Technology 205 (2010), p. 1830-1837
doi: 10.1016/j.surfcoat.2010.07.126

Banhart, J.; Borbely, A.; Dzieciol, K.; Garcia-Moreno, F.; Manke, I.; Kardjilov, N.; Kaysser-Pyzalla, A.R.; Strobl, M.; Treimer, W.: X-ray and neutron imaging - Complementary techniques for materials science and engineering. , International Journal of Materials Research 101 (2010), p. 1069-1079
doi: 10.3139/146.110382

2009

Klaus, M.; Reimers, W.; Genzel, Ch.: Application of Energy-Dispersive Diffraction to the Analysis of Highly Inhomogeneous Residual Stress Fields in Thin Film Structures. , In: Proceedings of the 57th Annual Conference on Applications of X-ray Analysis (Denver X-ray Conference) and the 8th International Conference on Residual Stresses (ICRS-8) ; 4 - 8 August 2008, Denver Marriott Tech Center Hotel, Denver, Colorado, USA . Newton Square, Pa.: Internat. Centre for Diffraction Data, 2009 (Advances in X-ray analysis ; 52), p. 429-436

Uhlmann, E.; Byrne, F.; Reimers, W.; Klaus, M.: Drehen von AlSi-Legierungen mit CVD-diamantbeschichteten Werkzeugen. , In: Forschung in Bewegung : 9. Magdeburger Maschinenbau-Tage ; 30.09. - 01.10.2009 ; Tagungsband. Univ. , Magdeburg, 2009, p. [1-13]

Bartosik, Matthias: Eigenspannungsgradienten in kugelgestrahlten TiN- und TiCN-Schichten charakterisiert mittels Hochtemperatur-Röntgenbeugung. , Montanuniversität Leoben, Diplom, 2009

Rodriguez-Alvarez, H.; Kötschau, I.M.; Genzel, C.; Schock, H.-W.: Growth paths for the sulfurization of Cu-rich Cu/In thin films. , Thin Solid Films 517 (2009), p. 2140-2144
doi: 10.1016/j.tsf.2008.10.091

Kromm, A.; Kannengiesser, T.: In-situ-phase analysis using synchrotron radiation of low transformation temperature (LTT) welding material. , Revista Soldagem & Inspeção 14 (2009), p. 82-88
doi: 10.1590/S0104-92242009000100010

Multigner, M.; Fernandez-Castrillo, P.; Ferreira-Barragans, S.; Gonzalez-Doncel, G.; Gonzalez-Carrasco, J.L.: Influencia del arenado de la aleacion Ti6Al4V en la dureza subsuperficial y estado de tensiones residuales = Influence of sandblasting of Ti6Al4V alloy on the subsurface hardness and residual stresses state. , Revista de Metalurgia 45 (2009), p. 52-57
doi: 10.3989/revmetalm.0803

Maawad, E.; Brokmeier, H.-G.; Wagner, L.; Genzel, C.: Investigation of Near-Surface Stress Gradients in Shot Peened Ti-2.5Cu Measured by Mechanical and Diffraction Methods. , In: H. El-Hofy [Ed.] : Proceedings of the 9th International Conference on Production Engineering, Design and Control : Alexandria, Egypt, 10-12 February 2009 . , 2009, p. 1-9

2008

Denks, Ingwer Asmus: Entwicklung einer Methodik zur Erfassung randschichtnaher Eigenspannungsverteilungen σ(z) in polykristallinen Werkstoffen mittels energiedispersiver Diffraktion. , Universität Kassel, 2008

EDDI