Optimum band gap for hybrid silicon/perovskite tandem solar cell
Sketch of the tandem cell. © H. Cords/HZB
Tandem solar cells based on silicon and perovskites have raised high hopes for future high efficiency solar modules. A team led by perovskite solar cell pioneer Henry Snaith at the University of Oxford has now shown, with contributions by Bernd Rech and Lars Korte of the Helmholtz-Zentrum Berlin, that an ultimate efficiency of 30% should be attainable with such tandem cells. They discovered a structurally stable perovskite composition with its band gap tuned to an optimum value of 1.75 eV. The results have been published in "Science".
Tandem solar cells based on silicon and perovskites have raised high hopes for future high efficiency solar modules (see also results here). A tandem solar cell works by absorbing the high energy photons (visible light) in a top cell which generates a high voltage, and the lower energy photons (Infra red) in a rear cell, which generates a lower voltage. This increases the theoretical maximum efficiency by about 50% in comparison to a standalone silicon cell.
To maximise efficiency, the amount of light absorbed in top cell has to precisely match the light absorbed in the rear cell. However, the band gap of ~1.6eV of the standard perovskite material is too small to fully exploit the efficiency potential of this technology.
A team led by perovskite solar cell pioneer Prof. Henry Snaith FRS at the University of Oxford, in collaboration with silicon solar cell experts Prof. Bernd Rech and Dr. Lars Korte of the Helmholtz-Zentrum Berlin, have shown that an ultimate efficiency of 30% should be attainable with such tandem cells.
They conceived together a tandem cell, in a configuration where the perovskite and the silicon cell are mechanically stacked and contacted separately. The HZB team contributed the silicon cell. The Oxford group did vary systematically the chemical composition of the perovskite layer, and with a precise cocktail of ions discovered a structurally stable perovsksite with its band gap tuned to an optimum value of 1.75 electron volts, maintaining a high electronic quality of the layer. At the same time, they increased the chemical and thermal stability of the material significantly.
Science 8 January 2016: Vol. 351 no. 6269 pp. 151-155
A mixed-cation lead mixed-halide perovskite absorber for tandem solar cells
- Cool vaccines in rural Kenya: solar solution has been awarded by UNIn May 2026, Tabitha Awuor Amollo is spending some weeks as a guest scientist at HZB, analysing perovskite thin films at BESSY II. The Kenyan physicist from Egerton University, Nairobi, was recently recognised for her achievements in research and teaching. For the development of a solar-powered refrigeration system for use in rural health centres, she has been awarded the 2026 Organization for Women in Science for the Developing World (OWSD)-Elsevier Foundation Award. An interview on exceptional projects and daily struggles of a scientist. Questions were asked by Antonia Rötger.
- BESSY II: How intrinsic oxygen shortens the lifespan of solid-state batteriesAlthough solid-state batteries (SSBs) demonstrate high performance and are intrinsically safe, their capacity currently declines rapidly. A team from the TU Wien, Humboldt-University Berlin and HZB has now analysed a TiS₂|Li₃YCl₆ solid-state half-cell in operando at BESSY II using a special sample environment that allows for non-destructive investigation under real operating conditions. Data obtained by combination of soft and hard X-ray photoelectron spectroscopy (XPS and HAXPES) revealed a new degradation mechanism that had not previously been identified in solid-state batteries. They have gained some surprising insights, particularly regarding the harmful role played by intrinsic oxygen. This study provides valuable information for improving design and handling of such batteries.
- Electrocatalysts: New model for charge separation at the solid-liquid interfaceHydrogen is at the heart of the transition to carbon neutrality, as both an energy carrier and a reagent for green chemistry. However, large-scale production of hydrogen via electrolysis, as well as the production of many other chemical products, requires significantly cheaper and more efficient catalysts. A precise understanding of the electrochemical processes that take place at the interface between the solid catalyst and the liquid medium is highly useful for developing better electrocatalysts. In the journal Nature Communications, an European team has now presented a powerful model that determines charge separation at the interface, the formation of the electric double layer and local electric potential variations, and the resulting influence on the catalytic activity.