X-ray analysis of carbon nanostructures helps material design
Schematic view of carbon structures with pores. © HZB
The intensity of the single peak increases as the chlorination temperature increases and carbons show increased order. © HZB
Nanostructures made of carbon are extremely versatile: they can absorb ions in batteries and supercapacitors, store gases, and desalinate water. How well they cope with the task at hand depends largely on the structural features of the nanopores. A new study from the HZB has now shown that structural changes that occur due to morphology transition with increasing temperature of the synthesis can also be measured directly – using small-angle X-ray scattering. The results have now been published in the journal Carbon.
Optimized nanoporous carbons can serve as electrodes for fast electron and ion transport or improve the performance of energy storage and conversion devices. Thus the tunability of the size, shape, and distribution of pores is highly required. The team at the HZB Institute for Soft Matter and Functional Materials collaborated with a group at the University of Tartu, Estonia, to inquire the nanoarchitecture, inner surface, size, form and distribution of nanopores in dependence of the synthesis conditions.
From 600 to 1000 degrees
Colleagues in Estonia produced a series of nanoporous carbons by reacting a powder of molybdenum carbide (Mo2C) with gaseous chlorine at 600, 700, 800, 900, and 1000 degrees Celsius. Depending on the synthesis conditions chosen, the nanoporous carbon exhibit different properties such as surface area, porosity, electronic and ionic conductivity, hydrophilicity and electrocatalytic activity.
Small Angle X-ray Scattering SAXS
Surface structures were analysed by transmission electron microscopy at the HZB. The interior surface area of nanocarbon materials is usually investigated by adsorption of gas. However, this method is not only comparatively inaccurate, it also contains no information about the shape and size of the pores. For deeper insights, Dr. Eneli Härk and her colleagues at HZB worked with small-angle X-ray scattering, a technique permitting to obtain information on various structural features on the nanometer scale including the mean pore size.
All about nanopores
Small-angle X-ray scattering not only provides information on the precise inner surface area and the average pore size, but also on their angularity, i.e., sharp edges of formed pores, which play a major role for the functionalization of the materials. “The SAXS analysis summarizes over an enormous amount of micropores omitting misleading assumptions thereby directly relating the nanostructural architecture of the material to macroscopic technical parameters under investigation in engineering” Härk explains.
The main aim was to understand structural formation, and electrochemical characteristics of carbon as a function of the synthesis temperature. “For optimal function, not only the high inner surface area is crucial, but the pores should have exactly the right shape, size and distribution”, says Härk.
The study is published in "Carbon" (2019): Carbide Derived Carbons Investigated by Small Angle X-ray Scattering: Inner Surface and Porosity vs. Graphitization; Eneli Härk, Albrecht Petzold, Günter Goerigk, Sebastian Risse, Indrek Tallo, Riinu Härmas, Enn Lust and Matthias Ballauff.
DOI: 10.1016/j.carbon.2019.01.076
- MXene as a frame for 2D water films shows new propertiesAn international team led by Dr. Tristan Petit and Prof. Yury Gogotsi has investigated MXene with confined water and ions at BESSY II. In the MXene samples, a transition between localised ice clusters to quasi-two-dimensional water films was identified by increasing temperature. The team also discovered that the intercalated water structure drives a reversible transition from metallic to semiconducting behaviour of the MXene film. This could enable the development of novel devices or sensors based on MXenes.
- Lithium-sulphur batteries with lean electrolyte: problem areas clarifiedUsing a non-destructive method, a team at HZB investigated practical lithium-sulphur pouch cells with lean electrolyte for the first time. With operando neutron tomography, they could visualise in real-time how the liquid electrolyte distributes and wets the electrodes across multilayers during charging and discharging. These findings offer valuable insights into the cell failure mechanisms and are helpful to design compact Li-S batteries with a high energy density in formats relevant to industrial applications.
- Self assembling monolayer can improve lead-free perovskite solar cells tooTin perovskite solar cells are not only non-toxic, but also potentially more stable than lead-containing perovskite solar cells. However, they are also significantly less efficient. Now, an international team has succeeded in reducing losses in the lower contact layer of tin perovskite solar cells: The scienstists identified chemical compounds that self-assemble into a molecular layer that fits very well with the lattice structure of tin perovskites. On this monolayer, tin perovskite with excellent optoelectronic quality can be grown, which increases the performance of the solar cell.