Green hydrogen: "Rust" as a photoanode and its limits
The HZB team was able to determine the photoconductivity in the thin layers of rust using time-resolved microwave measurements; here is a picture of the measurement setup. © HZB
Rust would be an extremely cheap and stable photoelectrode material to produce green hydrogen with light. But the efficiency is limited. The TEM image shows a photoanode containing a thin photoactive layer of rust. © Technion
Metal oxides such as rust are intriguing photoelectrode materials for the production of green hydrogen with sunlight. They are cheap and abundant, but in spite of decades of research, progress has been limited. A team at HZB, together with partners from Ben Gurion University and the Technion, Israel, has now analysed the optoelectronic properties of rust (haematite) and other metal oxides in unprecedented detail. Their results show that the maximum achievable efficiency of haematite electrodes is significantly lower than previously assumed. The study demonstrates ways to assess new photoelectrode materials more realistically.
Hydrogen will be needed in large quantities as an energy carrier and raw material in the energy system of the future. To achieve this, however, hydrogen must be produced in a climate-neutral way, for example through so-called photoelectrolysis, by using sunlight to split water into hydrogen and oxygen. As photoelectrodes, semiconducting materials are needed that convert sunlight into electricity and remain stable in water. Metal oxides are among the best candidates for stable and inexpensive photoelectrodes. Some of these metal oxides also have catalytically active surfaces that accelerate the formation of hydrogen at the cathode or oxygen at the anode.
Why is rust not much better?
Research has long focused on haematite (α-Fe2O3), which is widely known as rust. Haematite is stable in water, extremely inexpensive and well suited as a photoanode with a demonstrated catalytic activity for oxygen evolution. Although research on haematite photoanodes has been going on for about 50 years, the photocurrent conversion efficiency is less than 50% of the theoretical maximum value. By comparison, the photocurrent efficiency of the semiconductor material silicon, which now dominates almost 90% of the photovoltaic market, is about 90% of the theoretical maximum value.
Scientists have puzzled over this for a long time. What exactly has been overlooked? What is the reason that only modest increases in efficiency have been achieved?
Israeli-German team solves the puzzle
In a recent study published in Nature Materials, however, a team led by Dr. Daniel Grave (Ben Gurion University), Dr. Dennis Friedrich (HZB) and Prof. Dr. Avner Rothschild (Technion) has provided an explanation as to why haematite falls so far short of the calculated maximum value. The group at Technion investigated how the wavelength of absorbed light in hematite thin films affects the photoelectrochemical properties, while the HZB team determined the wavelength dependent charge carrier properties in thin films of rust with time-resolved microwave measurements.
Fundamental physical property extracted
By combining their results, the researchers succeeded in extracting a fundamental physical property of the material that had generally been neglected when considering inorganic solar absorbers: The photogeneration yield spectrum. "Roughly speaking, this means that only part of the energy of the light absorbed by haematite generates mobile charge carriers, the rest generates rather localised excited states and is thus lost," Grave explains.
Rust will not get much better
"This new approach provides experimental insight into light-matter interaction in haematite and allows distinguishing its optical absorption spectrum into productive absorption and non-productive absorption," Rothschild explains. "We could show that the effective upper limit for the conversion efficiency of haematite photoanodes is significantly lower than that expected based on above band-gap absorption," says Grave. According to the new calculation, today's “champion” haematite photoanodes have already come quite close to the theoretically possible maximum. So it doesn't get much better than that.
Assessing new photoelectrode materials
The approach has also been successfully applied to TiO2, a model material, and BiVO4, which is currently the best-performing metal oxide photoanode material. “With this new approach, we have added a powerful tool to our arsenal that enables us to identify the realizable potential of photoelectrode materials. Implementing this to novel materials will hopefully expedite the discovery and development of the ideal photoelectrode for solar water splitting. It would also allow us to ‘fail quickly’, which is arguably just as important when developing new absorber materials“ says Friedrich.
- Only at BESSY II worldwide: IR nanoscopy at very long THz wavelengthsThe team at the IRIS beamline at BESSY II has created a new experimental option: They achieved infrared nanoscopy with a spatial resolution of around 50 nm at very long THz wavelengths. This was possible thanks to a temporal pattern of light pulses known as the low-alpha operating mode at BESSY II. Worldwide, BESSY II is the only synchrotron light source at which users could perform nanoscopy in a single setup from 25 to 4000 cm-1, a unique opportunity for ultra-broadband characterisation of complex materials at the nanoscale in both the life sciences and materials sciences.
- Ultrafast demagnetisation - Thinner iron, stronger effectThe thinner an iron film, the more easily it can be demagnetised by a laser pulse. Researchers at the University of Duisburg-Essen, working with Helmholtz-Zentrum Berlin and other partners, have discovered why: the key lies in the magnetic order at the material's interfaces. In the long term, these findings could contribute to the development of new technologies for magnetic data storage. The results have been published in the scientific journal Advanced Science.
- Blind spot for the arrangement of atomsArtificial intelligence is increasingly being used to predict the properties of new materials. A research team from Jena and the United States now shows in a study published in the journal Nature Computational Science that when language models are used for this purpose, they reliably identify which types of atoms a material contains. However, they make insufficient use of information about how those atoms are arranged in space. Neither larger models nor additional training data resolve this weakness. For material properties that depend strongly on structure, AI models specifically designed to process spatial relationships are therefore the more reliable choice. (DOI: 10.1038/s43588-026-01045-2)