Insight into loss processes in perovskite solar cells enables efficiency improvements
The analysed perovskite cell has a surface of 1 cm2. Credit. Uni Potsdam © Uni Potsdam
With additional layers between the perovskite semiconductor and the hole- and electron-transportlayers (red and blue lines), the team at the University of Potsdam was able to further increase efficiency of the perovskite cell. Bild. Uni Potsdam © Uni Potsdam
In perovskite solar cells, charge carriers are mainly lost through recombination occurring at interface defect sites. In contrast, recombination at defect sites within the perovskite layer does not limit the performance of the solar cells at present. Teams from the University of Potsdam and the Helmholtz-Zentrum Berlin (HZB) were able to reach this interesting conclusion through extremely accurate quantitative measurements on 1 cm2 perovskite cells using photoluminescence. Their results contribute to improving perovskite solar cells and have now been published in Nature Energy.
Even solar cells made of a perfect miracle material would never be able to convert 100 % of sunlight to electrical energy. This is because the theoretical maximum achievable power is limited by the position of the energy bands of the electrons, and by unavoidable radiation of photons (the thermodynamic or Shockley-Queisser limit). Maximum power conversion efficiency for silicon is about 33 %, for example. But even this value will never actually be reached. This is due to defects of various kinds causing the loss of some of the charge carriers released by sunlight. In order to approach the maximum value, it is therefore necessary to investigate the various defects in solar cells and determine which ones lead to losses and how.
Organometallic perovskite absorber layers are regarded as a particularly exciting new material class for solar cells – in just ten years, their efficiency has increased from three per cent to over twenty per cent, an amazing success story. Now a team headed by Prof. Dr. Dieter Neher at the University of Potsdam and Dr. Thomas Unold at HZB has succeeded in identifying the decisive loss processes in perovskite solar cells that limit the efficiency.
At certain defects in the crystal lattice of the perovskite layer, charge carriers (i.e. electrons and “holes“) that have just been released by sunlight can recombine again and thus be lost. But whether these defects were preferentially located within the perovskite layer, or instead at the interface between the perovskite layer and the transport layer was unclear until now.
To determine this, the scientists employed photoluminescence techniques with high precision, spatial and temporal resolution. Using laser light, they excited the square-centimetre-sized perovskite layer and detected where and when the material emitted light in response to the excitation. “This measurement method at our lab is so precise, we can determine the exact number of photons that have been emitted”, explains Unold. And not only that, the energy of the emitted photons was precisely recorded and analyzed as well using a hyperspectral CCD camera.
“In this way, we were able to calculate the losses at every point of the cell and thereby determine that the most harmful defects are located at the interfaces between the perovskite absorber layer and the chargetransport layers“, reports Unold. This is important information for further improving perovskite solar cells, for instance by means of intermediate layers that have a positive effect or through modified fabrication methods.
With the help of these findings, the group led by Prof. Dr. Dieter Neher and Dr. Martin Stolterfoht at the University of Potsdam has succeeded in reducing interfacial recombination and thus increasing the efficiency of 1cm2sized perovskite solar cells to well over 20 %.
Published in Nature Energy (2018):Visualization and suppression of interfacial recombination for high-efficiency large-area pin perovskite solar cells; Martin Stolterfoht, Christian M. Wolff, José A. Márquez, Shanshan Zhang,Charles J. Hages,Daniel Rothhardt, Steve Albrecht, Paul L. Burn, Paul Meredith, Thomas Unold and Dieter Neher
Doi:10.1038/s41560-018-0219-8
- Iridium-free catalysts for acid water electrolysis investigatedHydrogen will play an important role, both as a fuel and as a raw material for industry. However, in order to produce relevant quantities of hydrogen, water electrolysis must become feasible on a multi-gigawatt scale. One bottleneck is the catalysts required, with iridium in particular being an extremely rare element. An international collaboration has therefore investigated iridium-free catalysts for acidic water electrolysis based on the element cobalt. Through investigations with various methods, among them experiments at the LiXEdrom at the BESSY II X-ray source in Berlin, they were able to elucidate processes that take place during water electrolysis in a cobalt-iron-lead oxide material as the anode. The study is published in Nature Energy.
- Lithium-sulphur batteries with lean electrolyte: problem areas clarifiedUsing a non-destructive method, a team at HZB investigated practical lithium-sulphur pouch cells with lean electrolyte for the first time. With operando neutron tomography, they could visualise in real-time how the liquid electrolyte distributes and wets the electrodes across multilayers during charging and discharging. These findings offer valuable insights into the cell failure mechanisms and are helpful to design compact Li-S batteries with a high energy density in formats relevant to industrial applications.
- Self assembling monolayer can improve lead-free perovskite solar cells tooTin perovskite solar cells are not only non-toxic, but also potentially more stable than lead-containing perovskite solar cells. However, they are also significantly less efficient. Now, an international team has succeeded in reducing losses in the lower contact layer of tin perovskite solar cells: The scienstists identified chemical compounds that self-assemble into a molecular layer that fits very well with the lattice structure of tin perovskites. On this monolayer, tin perovskite with excellent optoelectronic quality can be grown, which increases the performance of the solar cell.