Accelerator Physics: HF-Couplers for bERLinPro prove resilient
For the measurement campaign, two couplers were mounted in a horizontal test position under a local clean room tent. © A. Neumann/HZB
To generate the HF power, a 270 kW klystron is needed, among other things. © A. Neumann/HZB
In synchrotron light sources, an electron accelerator brings electron bunches to almost the speed of light so that they can emit the special "synchrotron light". The electron bunches get their enormous energy and their special shape from a standing electromagnetic alternating field in so-called cavities. With high electron currents, as required in the bERLinPro project, the power needed for the stable excitation of this high-frequency alternating field is enormous. The coupling of this high power is achieved with special antennas, so-called couplers, and is considered a great scientific and technical challenge. Now, a first measurement campaign with optimised couplers at bERLinPro shows that the goal can be achieved.
These couplers should supply the cavities with 230 kW in continuous operation at 1.3 GHz. The connection between the ultra-high vacuum of the cavities and the high-frequency transmission link must be guaranteed, both at liquid helium temperature (-269 degrees Celsius or 4 Kelvin) and at room temperature. In addition, clean room conditions must be maintained and particles down to the micrometre range must be removed. The power is to be transferred to the cavity by two couplers each, in order to reduce the individual load, but also to improve the stability of the electron trajectory in the accelerator.
High-performance couplers modified
Now, the team led by Axel Neumann from the HZB Institute SRF (Superconducting Radio Frequency Technologies) has been able to show that this goal is realistic. To do so, they modified the design of the high-performance couplers of a research group from the National Research Centre for High Energy Physics in Japan (KEK).
Measurements up to 45 kW
For the measurement campaign, two of the newly developed couplers were set up in tandem with a test box as a cavity substitute. The measurements started with low power, which was gradually increased up to 45 kW. Initially, only short pulses were transmitted from the couplers to the cavity at longer intervals, here even up to powers of 100 kW. Then the intervals between the power pulses became shorter and shorter up to continuous operation.
Good News: heat can be dissipated
The heat development was 0.25 Kelvin per kilowatt of power. At a final power of 120 kW, the material would heat up by about 30 degrees Kelvin. This is good news, because such amounts of heat are technically dissipatable through the planned cooling. "With the original Japanese design, the heat generation was higher by a factor of four than with our adapted form," explains Neumann.
Outlook: 120 kW
"We initially limited the measurements to power levels below 45 kW. Only when all couplers have been successfully tested at these powers will the next steps come. However, we are now very optimistic. If you extrapolate the figures, the coupler should indeed manage 120 kW in continuous operation without any problems," says Prof. Dr. Jens Knobloch, who heads the HZB Institute SRF Science and Technology.
Helmholtz-Programme for Accelerator Physics (ARD)
With its work on high-frequency cavities, HZB is contributing to the Helmholtz Association's research programme for accelerator physics (ARD = "Accelerator Research and Development"). A central topic of ARD is the development of superconducting high-frequency systems for accelerating high currents in continuous wave operation. Just recently, ARD was evaluated by an international panel and received top marks in all categories.
- BESSY II: High-resolution insights into individual biomolecules and catalystsVery small biological samples and even individual biomolecules can now be examined under near-physiological conditions with high confidence at the BESSY II infrared beamline with a newly validated and improved technique: The nanoscale infrared spectroscopy (s-SNOM) with ultra-thin silicon-based membranes. An international team demonstrated after an initial proof of concept, that high-resolution (a few tens of nanometres) nano-IR measurements reliably match expected far-field IR spectra in an aqueous environment. This methodological advance provides a solid foundation for studying biomaterials or observing catalytic processes in a liquid environment.
- New method shows how molecular switches are influenced by their neighborsResearchers at Friedrich Schiller University Jena and the Helmholtz Centre Berlin (HZB) have, for the first time, been able to directly observe how the environment surrounding a molecular switch influences its electronic structure. Molecular switches are molecules that can be switched between two states by external influences such as changes in temperature—similar to a switch with the positions »On« and »Off«. Such molecules are being investigated as potential building blocks for future data storage devices or sensor materials. Using magnetic-field-dependent terahertz spectroscopy, the researchers have now, for the first time, been able to distinguish whether neighbouring molecules in a material are in the same or different states. The results have been published in the journal »Angewandte Chemie International Edition«.
- BESSY II is back in operation after maintenance shutdownOn 7 September 2026, BESSY II was set into operation after a four-week shutdown. BESSY II is scheduled to resume full user operation on 22 September.