"Green" chemistry: BESSY II sheds light on mechanochemical synthesis
Finely ground powders can also react with each other without solvents to form the desired product. This is the approach of mechanochemistry. © F. Emmerling/BAM
The reagents are ground in a ball mill, and the formation of new products and phases can be followed via X-ray structure analysis at BESSY II. Picture: F. Emmerling/BAM © F. Emmerling/BAM
In mechanochemistry, reagents are finely ground and mixed so that they combine to form the desired product, even without need for solvent. By eliminating solvent, this technology promises to contribute significantly towards ‘green’ and environmentally benign chemical manufacture in the future. However, there are still major gaps in understanding the key processes that occur during mechanical treatment and reaction. A team led by the Federal Institute for Materials Research (BAM) has now developed a method at BESSY II to observe these processes in situ with X-ray scattering.
Chemical reactions are often based on the use of solvents that pollute the environment. Yet, many reactions can also work without solvent. This is the approach known as mechanochemistry, in which reagents are very finely ground and mixed together so that they react with each other to form the desired product. The mechanochemical approach is not only more environmentally friendly, but even potentially cheaper than classical synthesis methods. The International Union of Pure and Applied Chemistry (IUPAC) therefore ranks mechanochemistry among the 10 chemical innovations that will change our world. However, the full potential of this technology cannot be realized until the processes during mechanical treatment are understood in more detail, so that it is possible to precisely direct and control them.
Understanding what exactly happens during mechanical treatment and how the reactions take place is difficult to study. Traditionally, this is done by stopping the reaction and removing the material from the reactor for analysis "ex situ." However, many systems continue their transformation even after the milling process is stopped. Such reactions can only be studied by directly examining the reaction in situ during mechanical treatment.
Time-resolved in situ monitoring
Now, an international team including Dr. Adam Michalchuk and Dr. Franziska Emmerling from the Federal Institute for Materials Research (BAM) and researchers at the University of Cambridge and University of Parma used BESSY II's μSpot beamline to develope a method to gain insight in situ and during mechanical treatment.
To do so, the team used a combination of miniaturized grinding jars together with innovations in X-ray powder diffraction and state-of-the-art analysis strategies to significantly increase the quality of data from time-resolved in situ monitoring (TRIS).
Very small samples
"Even with exceptionally small sample volumes, we get an accurate composition and structure of each phase over the course of the reaction," says Michalchuk. Even with sample amounts as small as a few milligrams, good results were possible. In addition, they can determine the crystal size and other important parameters. This strategy is applicable to all chemical species, is easy to implement, and provides high-quality diffraction data even with a low-energy synchrotron source.
"This provides a direct route to the mechanochemical study of reactions involving scarce, expensive or toxic compounds," Emmerling says.
- Nanosilver as an electrocatalyst for CO₂ reductionVia electrolysis, CO2 can be reduced to CO, a raw material for further chemical products such as fuels. Within the GreenQuest Project, an internation team led by HZB chemist Prashanth Menezes has now systematically investigated catalyst layers made of silver nanoparticles, varying both the size of the particles and their density. The best yield was achieved with nanoparticles with diameters of around 10 nm, which were loosely distributed. Furthermore, they demonstrated how the economic efficiency of the electrochemical cell can be enhanced by integrating an additional chemical reaction at the anode, enabling the simultaneous production of a valuable formic acid, hydrogen, and CO in one device.
- Spin waves inside a nano-oscillator imaged for the first timeFor the first time, researchers have directly imaged the magnetisation dynamics inside a spin Hall nano-oscillator — a nanoscale device that converts direct current into tunable microwave signals and is a promising building block for energy-efficient wireless communication and brain-inspired computing. A Swedish–German team led by the University of Gothenburg and Helmholtz-Zentrum Berlin (HZB) achieved this using time-resolved scanning transmission X-ray microscopy at the MAXYMUS instrument at BESSY II. The results, now published in Advanced Materials, reveal spin-wave features that had escaped previous, indirect measurement techniques.
- Joint power instead of duplicate structures:Berlin’s research community is further advancing its research excellence by establishing a high-performance, cross-institutional infrastructure for data and AI. With a joint agreement signed on 18 September 2026, the Berlin University Alliance (BUA), the Helmholtz-Zentrum Berlin (HZB) and the Zuse Institute Berlin (ZIB) are paving the way for a joint data science and AI centre in Berlin-Dahlem and Adlershof.