Inkjet printing process for Kesterite solar cells
Illustration of the working principle of inkjet printing. © HZB
Cross sectional scanning electron microscopy of a complete device. The Kesterite layer (CZTSSe) is printed on top of a Molybdenum substrate. © HZB
A research team at HZB has developed an inkjet printing technology to produce kesterite thin film absorbers (CZTSSe). Based on the inkjet-printed absorbers, solar cells with total area conversion efficiency of up to 6.4 % have been achieved. Although this is lower than the efficiency records for this material class, the inkjet printing minimizes waste and has huge advantages for industrial production.
The drop-on-demand inkjet printing is a promising approach allowing patterning of materials with negligible materials waste; hence, significant reduction of raw materials cost can be achieved. Furthermore, inkjet printing can be easily adapted to a roll-to-roll process, which is suitable for large scale production. From the industrial application perspective, both of these two features of the inkjet printing technology are of great interest. A critical requirement for using inkjet printing is to develop a suitable ink in terms of viscosity and stability which leads to compact and homogeneous films.
Tuning the molecular ink
Dr. Xianzhong Lin from the Institute for Heterogeneous Material Systems of HZB used a molecular ink which was originally developed for spin coating technologies. The ink is produced by dissolving Cu, Zn, Sn metal salt and thiourea in dimethyl sulfoxide solvent. Lin tested its suitability for inkjet printing. He found that the viscosity of the ink can be tuned by adjusting the ink concentration and the ink composition can also be easily controlled by adding or reducing the amount of each chemical added. The CZTSSe absorbers were formed by annealing the inkjet-printed Cu-Zn-Sn-S precursor film under an atmosphere containing Selenium.
Economical process
Initial optimization of the processing conditions such as ink composition and printing parameters have already yielded solar cells with efficiencies up to 6.4 %. The huge advantage of inkjet printing versus spin coating to obtain thin film absorbers is the lesser amount of waste: Whereas with spin coating, a large quantity of the ink material is wasted, the inkjet printing is very economical: For example, less than 20 microliter ink is needed to build up a micrometer CZTSSe thin film absorber on an inch by inch (corresponding to 6.5 cm2) substrate in this study.
Low toxicity and low waste
“Although the solar cell performance is still far below the record efficiency of 12.7 % for CZTSSe based solar cells, the great advantage of our approach is the low toxic and low material wastage process”, Prof. Martha Lux-Steiner explains. The team is now working on the optimization of processing conditions for the kesterite absorbers to further improve the solar cell performance and on the deposition of buffer and TCO layers by inkjet printing. The goal is to print a complete device with high efficiency without relying on expensive vacuum technology. This work opens up a promising route for the fabrication of kesterite thin film solar cells.
The results of this work have now been published in X. Lin, J. Kavalakkatt, M. C. Lux-Steiner, A. Ennaoui, Inkjet-printed Cu2ZnSn(S, Se)4 solar cells, Adv. Sci. 2015.
DOI: 10.1002/advs.201500028
Former results have been published here : X. Lin, J. Kavalakkatt, N. Brusten, M. C. Lux-Steiner, A. Ennaoui, Inkjet printing of Kesterite and Chalcopyrite thin film absorbers for low cost photovoltaic application, in 29th Eur. PV Solar Energy Conf., Vol. 3DV.2.64, Amsterdam 2014, 1876.
- Humboldt-Fellow at HZB-Institute for Solar Fuels: Alexander R. UhlAlexander R. Uhl, UBC Okanagan School of Engineering in Kelowna, Canada, aims to develop with Roel van de Krol from the HZB Institute for Solar Fuels an efficient and inexpensive photoelectrolyser for producing hydrogen using sunlight. His stay is being funded by the Alexander von Humboldt Foundation.
- 5000th protein structure at BESSY II: Starting point for a COVID drugMany proteins have a complex architecture that enables biological functions. Molecules can bind to specific sites on a protein and alter its function. A team at HZB has now investigated the Nsp1 protein, which plays a role in infection with the SARS-CoV-2 virus. They analysed protein crystals, previously mixed with molecules from a fragment library, and discovered a total of 21 candidates as starting points for drug development. At the same time, they also decoded the 5000th structure at BESSY II.
- Element cobalt exhibits surprising propertiesThe element cobalt is considered a typical ferromagnet with no further secrets. However, an international team led by HZB researcher Dr. Jaime Sánchez-Barriga has now uncovered complex topological features in its electronic structure. Spin-resolved measurements of the band structure (spin-ARPES) at BESSY II revealed entangled energy bands that cross each other along extended paths in specific crystallographic directions, even at room temperature. As a result, cobalt can be considered as a highly tunable and unexpectedly rich topological platform, opening new perspectives for exploiting magnetic topological states in future information technologies.