Artificial photosynthesis: New, stable photocathode with great potential

A <a href="" class="Extern">short filmclip</a> demonstrates the production of the photocathode with ILGAR method.

A short filmclip demonstrates the production of the photocathode with ILGAR method.

A scanning electron microscopy shows a cross section of the composite photocathode (left). By TEM analysis, platin nanoparticles could be identified in the TiO<sub>2</sub> thin film (right).

A scanning electron microscopy shows a cross section of the composite photocathode (left). By TEM analysis, platin nanoparticles could be identified in the TiO2 thin film (right). © HZB

A team at the HZB Institute for Solar Fuels has developed a new composite photocathode for generating hydrogen with high quantum efficiency using sunlight. This enables solar energy to be stored chemically.The photocathode consists of a thin film of chalcopyrite produced by HZB/PVcomB coated with a newly developed thin film of photoresistant titanium dioxide containing platinum nanoparticles. This layer does not only protect the chalcopyrite thin film from corrosion, it additionally acts as a catalyst to speed-up the formation of hydrogen as well as being a novel photodiode itself that even shows photoelectric current density and voltage comparable to those of a chalcopyrite-based thin film solar cell.

Many of us are familiar with electrolytic splitting of water from their school days: if you hold two electrodes into an aqueous electrolyte and apply a sufficient voltage, gas bubbles of hydrogen and oxygen are formed. If this voltage is generated by sunlight in a solar cell, then you could store solar energy by generating hydrogen gas.This is because hydrogen is a versatile medium of storing and using “chemical energy”. Research teams all over the world are therefore working hard to develop compact, robust, and cost-effective systems that can accomplish this challenge. But it is not that simple, because an efficient hydrogen generation preferably proceeds in an acidic electrolyte corroding very fast solar cells. Electrodes that so far have been used are made of very expensive elements such as platinum or platinum-iridium alloys.

New photocathode with several advantages

Under the “Light2Hydrogen” BMBF Cluster project and an on-going “Solar H2” DFG Priority programme, a team from the HZB Institute for Solar Fuels has now developed a novel photoelectrode that solves these problems: it consists of chalcopyrite (a material used in device grade thin film solar cells) that has been coated with a thin, transparent, conductive oxide film of titanium dioxide (TiO2). The special characteristics are: the TiO2 film is polycrystalline and contains a small amount of platinum in the form of nanoparticles. This new composite presents some special talents. Firstly, it produces under sun light illumination a photovoltage of almost 0.5 volts and very high photocurrent densities of up to 38 mA/cm2; secondly, it acts as a catalyst to accelerate the formation of hydrogen, and finally, it is chemically protected against corrosion as well. Since TiO2 is transparent, almost all sun  light reaches the photoactive chalcopyrite, leading to the observed high photocurrent density and photovoltage comparable with those of a conventional device-grade thin-film solar cell.

HZB recipe and technology

The recipe for this novel and elegant coating was developed by Anahita Azarpira in the course of her doctoral studies in a team headed by Assoc. Prof. Thomas Schedel-Niedrig. She uses a chemical vapour coating technique (sprayed ion-layer gas reaction/Spray-ILGAR) that was developed and patented at the HZB Institute for Heterogeneous Material Systems (EE-IH). In this process, the titanium dioxide and platinum precursors are dissolved in ethanol and converted to a fog using an ultrasonic bath. The produced aerosol is directed over the heated substrate using a stream of nitrogen gas resulting into a polycrystalline thin film grown on the chalcopyrite substrate over time with embedded nanoparticles of platinum.

More than 80 % of light converted

Azarpira and her colleagues varied the amount of platinum in the precursor solution in order to optimize the properties of the novel composite photoelectrode device.The properties were optimal with a volumetric proportion of about 5 % platinum (H2PtCl6) in the precursor solution.“ More than 80 % of the incident visible sunlight was photoelectrically converted by this composite system into electric current available for the hydrogen generation”, says Schedel-Niedrig. That means little light is lost and the quantum efficiency is virtually very high. In addition, it has been reported in the very recently published article that the composite shows high long-term stability over 25 hours and reveals large photoelectrocatalytic activity of about 690 hydrogen molecules produced per second and per active center at the surface under illumination.

Feasibility demonstrated

However, there is still a lot to do. Currently, the majority of the required voltage between the composite photocathode and a platinum counter electrode of around 1.8 volts is still coming from a battery. Hence the solar-to-hydrogen efficiency has to be clearly improved. “But anyway, we demonstrate the feasibility of such future-oriented chemical robust photoelectrocatalytic systems that have the potential to convert solar energy to hydrogen, i.e to chemical energy for storage. As a consequence we have successfully developed and tested a demonstrator device for solar hydrogen production with a company in Schwerin under the Light2Hydrogen project,” according to Schedel-Niedrig.

Publikation: Azarpira, A., Lublow, M., Steigert, A., Bogdanoff, P., Greiner, D., Kaufmann, C. A., Krüger, M., Gernert, U., van de Krol, R., Fischer, A. and Schedel-Niedrig, T. (2015), Efficient and Stable TiO2:Pt–Cu(In,Ga)Se2 Composite Photoelectrodes for Visible Light Driven Hydrogen Evolution. Adv. Energy Mater.. doi: 10.1002/aenm.201402148

PS:We demonstrate the production of the composit photocathode in a short filmclip in our HZBkanal.


You might also be interested in

  • Stability of perovskite solar cells reaches next milestone
    Science Highlight
    Stability of perovskite solar cells reaches next milestone
    Perovskite semiconductors promise highly efficient and low-cost solar cells. However, the semi-organic material is very sensitive to temperature differences, which can quickly lead to fatigue damage in normal outdoor use. Adding a dipolar polymer compound to the precursor perovskite solution helps to counteract this. This has now been shown in a study published in the journal Science by an international team led by Antonio Abate, HZB. The solar cells produced in this way achieve efficiencies of well above 24 %, which hardly drop under rapid temperature fluctuations between -60 and +80 Celsius over one hundred cycles. That corresponds to about one year of outdoor use.
  • Recommended reading: Bunsen magazine with focus on molecular water research
    Recommended reading: Bunsen magazine with focus on molecular water research
    Water not only has some well-known anomalies, but is still full of surprises. The first issue 2023 of the Bunsen Magazine is dedicated to molecular water research, from the ocean to processes in electrolysis. The issue presents contributions from researchers cooperating within the framework of a European research initiative in the "Centre for Molecular Water Science" (CMWS). A team at HZB presents results from the synchrotron spectroscopy of water. Modern X-ray sources can be used to study molecular and electronic processes in water in detail.
  • New software based on Artificial Intelligence helps to interpret complex data
    Science Highlight
    New software based on Artificial Intelligence helps to interpret complex data
    Experimental data is often not only highly dimensional, but also noisy and full of artefacts. This makes it difficult to interpret the data. Now a team at HZB has designed software that uses self-learning neural networks to compress the data in a smart way and reconstruct a low-noise version in the next step. This enables to recognise correlations that would otherwise not be discernible. The software has now been successfully used in photon diagnostics at the FLASH free electron laser at DESY. But it is suitable for very different applications in science.