Climate change: How could artificial photosynthesis contribute to limiting global warming?

<p class="MsoPlainText">The atmosphere can be compared to a bathtub that can only be filled to its rim if global warming is to be limited to a certain level. We could create another small outward flow with negative emissions. However, there is no way around turning off the tap.

The atmosphere can be compared to a bathtub that can only be filled to its rim if global warming is to be limited to a certain level. We could create another small outward flow with negative emissions. However, there is no way around turning off the tap. © M.May/HZB

If CO2 emissions do not fall fast enough, then CO2 will have to be removed from the atmosphere in the future to limit global warming. Not only could planting new forests and biomass contribute to this, but new technologies for artificial photosynthesis as well. An HZB physicist and a researcher at the University of Heidelberg have estimated how much surface area such solutions would require. Although artificial photosynthesis could bind CO2 more efficiently than the natural model, there are still no large modules that are stable over the long term. The team published their calculations in "Earth System Dynamics".

After several years during which global emissions at least stagnated, they rose again somewhat in 2017 and 2018. Germany has also clearly missed its climate targets. In order to keep global warming below 2 degrees Celsius, only about 1100 gigatonnes of CO2 may be released into the atmosphere by 2050[1]. And In order to limit global warming to 1.5 degrees, only just under 400 gigatonnes of CO2 may be emitted worldwide. By 2050, emissions will have to fall to zero even. Currently, however, 42 gigatonnes of CO2 are added every year.

Almost all the various scenarios require “negative emissions”

The Intergovernmental Panel on Climate Change (IPCC) has numerically simulated various scenarios. Only in the most optimistic scenario can the climate target still be achieved by means of immediate and drastic measures in all sectors (transport, agriculture, construction, energy, etc.). In the less optimistic scenarios, the global community will have to take additional measures beginning in 2030 or by 2050 at the latest: we will have to implement “negative emissions” by removing large quantities of CO2 from the atmosphere and store them permanently in order to balance the carbon budget. One example of negative emissions is large-scale forestation – forests bind CO2 in wood as long as it is not later used as fuel. But CO2 could also be removed from the atmosphere and bound using artificial photosynthesis. 

Physicists have now calculated how this might work. Dr. Matthias May of the HZB Institute for Solar Fuels is an expert in artificial photosynthesis. Dr. Kira Rehfeld is an environmental physicist at the University of Heidelberg studying climate and environmental variability.

Natural photosynthesis: a surface area the size of Europe would have to be forested

In a median scenario, at least 10 gigatonnes of CO2 per year would have to be removed from the atmosphere beginning around 2050 to balance the climate carbon budget. Forestation and cultivation of biomass for reducing CO2 compete for the same areas as are needed for agriculture, however. With just more biomass alone, it is therefore difficult to reach this scale, for natural photosynthesis is not a particularly efficient process. Leaves are able to use a maximum of two per cent of the light for converting CO2 and water into new chemical compounds. The two physicists argue that in order to bind 10 gigatonnes of CO2 per year in the forest, about 10 million square kilometres of the fertile areas on Earth would have to be planted with new forest. This corresponds to the area of continental Europe (up to the Urals!).

With artificial photosynthesis, an area the size of the State of Brandenburg could suffice

Materials systems currently being researched for artificial photosynthesis might bind CO2 with considerably greater efficiency. Already today, on a lab scale, photo-electrochemical systems made of semiconductor materials and oxides can utilise about nineteen per cent of the light to split water, for example, and thus realize part of the photosynthesis process. However, the material system envisaged by May and Rehfeld is not about producing hydrogen with sunlight, but instead about binding CO2 molecules and converting them into stable chemical compounds. „However, this is a relatively similar problem from the point of view of physical chemistry”, says May.

The prerequisite, however, is that it will be possible to develop by 2050 large-scale, durable modules that use solar energy to convert atmospheric CO2 into other compounds. The required area for this solution can be calculated. Assuming efficiency of nineteen per cent and fifty per cent system losses, around 30,000 square-kilometres of modules could be sufficient to extract 10 gigatonnes of CO2 from the atmosphere annually. This corresponds to the approximate area of the German federal State of Brandenburg.

"These kinds of modules could be placed in non-agricultural regions – in deserts, for example. In contrast to plants, they require hardly any water to operate, and their efficiency does not suffer when exposed to intense solar radiation,” explains May. The extracted CO2 could be converted to formic acid, alcohol or oxalate and combined with other compounds (such as calcium chloride) to form solid minerals that can be stored or even used in the form of plastic as a building material.

Focus on development, not on miracles

Even if May and Rehfeld are convinced that such solutions should be considered more closely, they warn against relying on technical miracles. This is because such systems still only function at the smallest scale, are expensive, and not stable in the long term. Changing this requires large investments in research and development.

“It might be possible to develop such modules, but even if we could then build them, we estimate that the conversion will cost at least 65 euros per tonne of CO2. The extraction of 10 gigatonnes of CO2 thus results in costs of 650 billion euros each year. Moreover, negative emissions can only be the last resort to slow dramatic climate developments. The best thing now would be to drastically reduce emissions immediately – that would be safer and much cheaper”, says May.

The study is published in 'Earth System Dynamics' 2019: ESD Ideas: Photoelectrochemical carbon removal as negative emission technology; Matthias M. May and Kira Rehfeld


[1]  Source: IPCC SR15 Report, those given values are necessary to reach the goal with a probability of 66 %. For higher probabilities, stricter reductions must be attained. A short explanation can be found here:


You might also be interested in

  • Freeze casting - a guide to creating hierarchically structured materials
    Science Highlight
    Freeze casting - a guide to creating hierarchically structured materials
    Freeze casting is an elegant, cost-effective manufacturing technique to produce highly porous materials with custom-designed hierarchical architectures, well-defined pore orientation, and multifunctional surface structures. Freeze-cast materials are suitable for many applications, from biomedicine to environmental engineering and energy technologies. An article in "Nature Reviews Methods Primer" now provides a guide to freeze-casting methods that includes an overview on current and future applications and highlights characterization techniques with a focus on X-ray tomoscopy.
  • IRIS beamline at BESSY II extended with nanomicroscopy
    Science Highlight
    IRIS beamline at BESSY II extended with nanomicroscopy
    The IRIS infrared beamline at the BESSY II storage ring now offers a fourth option for characterising materials, cells and even molecules on different length scales. The team has extended the IRIS beamline with an end station for nanospectroscopy and nanoimaging that enables spatial resolutions down to below 30 nanometres. The instrument is also available to external user groups. 

  • A simpler way to inorganic perovskite solar cells
    Science Highlight
    A simpler way to inorganic perovskite solar cells
    Inorganic perovskite solar cells made of CsPbI3 are stable over the long term and achieve good efficiencies. A team led by Prof. Antonio Abate has now analysed surfaces and interfaces of CsPbI3 films, produced under different conditions, at BESSY II. The results show that annealing in ambient air does not have an adverse effect on the optoelectronic properties of the semiconductor film, but actually results in fewer defects. This could further simplify the mass production of inorganic perovskite solar cells.